![background image](http://html.mh-extra.com/html/hilti/ncr-120-pc-a22/ncr-120-pc-a22_original-operating-instructions_2135073009.webp)
*2215656*
2215656
English
5
▶
Do not look directly into the light source (LEDs) of the power tool and do not aim the beam at other
persons’ faces. Risk of dazzling and you could injure the eyes.
▶
Keep the retaining strap and the tether clean and dry.
Electrical safety
▶
Before use of the crimping / pressing tool, all live cables and other equipment carrying electric voltage
within the area in which the user is working are to be switched off. If this is not possible, the corresponding
safety precautions for working in proximity to electrically live cables or equipment applicable in your
country must be implemented and observed.
▶
Before using the crimping / pressing tool, make sure there are no concealed electric cables or gas or
water pipes in the working area. External, metallic or electrically live parts can give you an electric shock
if you inadvertently damage electric cables or gas or water pipes.
▶
Do not crimp / press live parts, i.e. parts carrying electric voltage. The crimping / pressing tool must
be considered as being uninsulated and must therefore be used in combination with personal protective
equipment (protective gloves, protective footwear, protective clothing, etc.) of a type suitable to provide
protection for yourself and other persons in the vicinity. It is essential to ensure adequate insulation
for working in the vicinity of electrically live lines, for example by the use of solid insulating material or
maintenance of an adequate air gap. Among other uses, the crimping / pressing tool is suitable for use
on electrically insulating aerial lifts or platforms.
▶
In order to use the crimping / pressing tool in the vicinity of electrically live lines, the user must:
▶
take all different potentials (voltages) into account.
▶
make sure that all chosen measures and tools are appropriate for the application.
▶
be trained for working on electrically live lines.
▶
wear fit-for-purpose personal protective equipment.
▶
wear appropriate, close-fitting clothing.
▶
remove metallic lifestyle accessories such as jewelry.
Power tool use and care
▶
After approx. 50 consecutive crimping / pressing operations, switch the power tool off and allow it to
cool down for about 15 minutes. Overheating can lead to damage to the pressing tool.
▶
Store the pressing tool in a dry place inaccessible to children and unauthorized persons.
2.3
Careful handling and use of batteries
▶
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
▶
Do not expose batteries to high temperatures, direct sunlight or fire.
▶
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C
(176 °F).
▶
Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your
Hilti Service
.
▶
If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible
and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to
cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact
Hilti Service
.
Summary of Contents for NCR 120 PC-A22
