![background image](http://html.mh-extra.com/html/hilti/hit-fp-700-r/hit-fp-700-r_manual_2134973009.webp)
9
EN
Anchoring system for rebar fastenings in concrete.
Hilti HIT-FP 700 R
UFI: J6H3-V6YR-391K-G1QU (B)
(B)
Contains:
Lithium hydroxide (B);
L-(+)-tartaric acid (B)
Warning Causes skin irritation. (B) | Causes serious eye damage. (B) | Wear eye protection, protective clothing, protective
gloves. | Do not get in eyes, on skin or on clothing. | May damage fertility or the unborn child. (B) | IF IN EYES: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. | IF ON SKIN:
Wash with plenty of water. | If eye irritation persists: Get medical advice/attention. | If skin irritation or rash occurs: Get
medical advice/attention.
Contains 2-octyl-2H-isothiazol-3-one. May produce an allergic reaction.
Disposal considerations:
Empty packs:
Leave the mixer attached and dispose of via the local Green Dot recovery system or
EAK waste material code: 150102 plastic packaging.
Full or partially emptied packs:
Must be disposed of as special waste in
accordance with official regulations. EAK waste material code: 08 04 09* waste adhesives and sealants containing organic
solvents or other dangerous substances. or EAK waste material code: 20 01 27* paint, inks, adhesives and resins containing
dangerous substances.
Product Information:
Always keep this instruction for use together with the product. Ensure that the instruction for use is with
the product when it is given to other persons.
Material Safety Data Sheet:
Review the MSDS before use.
Check expiration date:
See expiration date imprint on foilpack manifold (month/year). Do not use expired product.
Base material temperature at time
of installation:
5 °C to 40 °C / 41°F to 104 °F.
Foil pack temperature during usage:
+5 °C to 40 °C / 41 °F to 104 °F.
Conditions
for transport and storage:
Keep in a cool, dry and dark place b5 °C to 25 °C / 41 °F to 77 °F. For any application not
covered by this document / beyond values specified, please contact Hilti. Working Times of mortar can vary in dry concrete.
Foil bag can only be used once.
Failure to observe these installation instructions, use of non-Hilti anchors, poor or questionable concrete conditions, or unique
applications may affect the reliability or performance of the fastenings.
NOTICE
Improper handling may cause mortar splashes.
Always wear safety glasses, gloves and protective clothes before handling
the mortar! | Never start dispensing without a mixer properly screwed on. | When using an extension hose: Discard of
initial mortar flow must be done through supplied mixer only (not through the extension hose). | Attach a new mixer prior to
dispensing a new foil pack (snug fit). | Caution! Never remove the mixer while the foil pack system is under pressure. Press
the release button of the dispenser to avoid mortar splashing. | Use only the type of mixer supplied with the mortar. Do not
modify the mixer in any way. | Never use damaged foil packs and/or damaged or unclean foil pack holders.
Poor load values / potential failure of fastening points due to inadequate borehole cleaning. The boreholes must be dry and
free of debris, dust, water, ice, oil, grease and other contaminants prior to mortar injection.
Hilti hollow drill bits TE-CD, TE-YD
must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric flow
rate) as specified in the accessory table. | For blowing out the borehole - blow out with oil free air until return air stream is free
of noticeable dust. | For flushing the borehole - flush with water line pressure until water runs clear. | Brushing of borehole
essential step in borehole preparation after hammer - and diamond drilling. | Important! Remove all water from the borehole
and blow out with oil free compressed air until borehole is completely dried before mortar injection. | Loading or manipulation of
rebar is not allowed within the setting time t
set
. Even if still within working time t
work
, do not touch the rebar anymore after setting
completion. | For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if
not the brush is too small and must be replaced. | Do not exceed the roughening time, when roughening the borehole.
Ensure that boreholes are filled from the back of the borehole without forming air voids.
If necessary, use the accessories /
extensions to reach the back of the borehole. | For overhead applications use the overhead accessories HIT-SZ / IP and take