background image

28

en

Noise information

as per German legislation (3, GSGV dated January 18, 1991):

The noise (power) level L

WA, 1S

as per § 1 (2) 1b) applicable to the tool and, due to different workplaces depend-

ing on the application for which the tool is used, also the noise (pressure) level L

pAImax

at the measurement sur-

face at a distance of 1 metre as per § 1 (2) 1e), are given in addition to the workplace related noise emission val-
ue in accordance with the noise measurement standard. Operating conditions and circumstances of use: most
powerful cartridge power load in accordance with instructions for use with suitable nail or stud fired vertically
downwards into a steel plate and in accordance with the means of measurement DIN 45635, part 34 “Measure-
ment of the noise emitted by powder-actuated fastening tools”.

Noise information 

- with red cartridge and power setting 2:

Application: Fastening metal profiles on concrete with the X-DNI 27 P8 nail.

1b) Noise(power) level 

L

WA, 1S

= 108 dB (A)

Workplace relevant emission value

L

pAImax

= 101 dB (A)

(measured at operator ear level)

1e) Noise (pressure) level

L’

pA, 1s

= 95 dB (A)

Variations in operating conditions may cause deviations from these noise emission values.

Summary of Contents for DX 462















Reviews: