background image

15

en

DX 462 powder-actuated tool

Warning signs

General

warning

Warning:

hot surface

Description of main parts

@

Exhaust gas piston return unit

;

Guide sleeve

=

Housing

%

Cartridge guideway

&

Power regulation wheel release button

(

Power regulation wheel

)

Trigger

+

Grip

§

Piston return unit release button

/

Ventilation slots

:

Piston rings

·

Piston *

$

Fastener guide *

£

Fastener guide release button

|

Buffer *

* These parts may be replaced by the user/operator.

Obligation signs

Wear eye

protection

Wear a

safety helmet

Wear ear

protection

Symbols

Read the opera-

tion instructions

before use

It is essential that the operating

instructions are read before the

tool is operated for the first time.

Always keep these operating

instructions together with the tool.

Ensure that the operating instruc-

tions are with the tool when it is

given to other persons.

Contents

Page

1. General information

15

2. Description

16

3. Accessories

17

4. Technical data

18

5. Safety rules

18

6. Before use

19

7. Operation

20

8. Care and maintenance

21

9. Troubleshooting

23

10. Disposal

27

11. Manufacturer’s warranty – DX tools

27

1. General information

1.1 Signal words and their meaning

WARNING

The word WARNING is used to draw attention to a poten-
tially dangerous situation which could lead to severe
personal injury or death.

CAUTION

The word CAUTION is used to draw attention to a poten-
tially dangerous situation which could lead to minor per-
sonal injury or damage to the equipment or other prop-
erty.

1.2 Pictograms

The numbers refer to the illustrations. The illustra-

tions can be found on the fold-out cover pages. Keep
these pages open while you read the operating instruc-
tions.

In these operating instructions, the designation “the
tool” always refers to the DX 462 powder-actuated tool.

Location of identification data on the tool

The type designation and the serial number are printed
on the type plate on the tool. Make a note of this infor-
mation in your operating instructions and always refer
to it when making an enquiry to your Hilti representa-
tive or service department.

Type:

DX 462

Serial no.:

Summary of Contents for DX 462















Reviews: