![background image](http://html.mh-extra.com/html/hilti/dag-700-p/dag-700-p_original-operating-instructions_2135612010.webp)
grounded power cord and grounded power supply
system.
b)
Avoid body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
c)
Don’t expose power tools to rain or wet condi-
tions.
Water entering a power tool will increase
the risk of electric shock.
d)
Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from an
outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged cords
immediately.
Damaged cords increase the risk
of electric shock.
e)
When operating a power tool outside, use an
outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce
the risk of electric shock.
2.1.3 Personal Safety
a)
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence
of drugs, alcohol or medication.
A moment of
inattention while operating power tools may result
in serious personal injury.
b)
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught
in moving parts.
c)
Avoid accidental starting. Be sure switch is
off before plugging in.
Carrying tools with your
finger on the switch or plugging in tools that have
the switch on invites accidents.
d)
Remove adjusting keys or switches before turn-
ing the tool on.
A wrench or a key that is left
attached to a rotating part of the tool may result
in personal injury.
e)
Do not overreach. Keep proper footing and bal-
ance at all times.
Proper footing and balance
enables better control of the tool in unexpected
situations.
f)
Use safety equipment. Always wear eye protec-
tion.
Dust mask, non-skid safety shoes, hard hat
or hearing protection must be used for appropri-
ate conditions.
2.1.4 Tool Use and Care
a)
Use clamps or other practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body is
unstable and may lead to loss of control.
b)
Do not force tool. Use the correct tool for your
application.
The correct tool will do the job better
and safer at the rate for which it is designed.
c)
Do not use tool if switch does not turn it on or
off.
Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
d)
Disconnect the plug from the power source be-
fore making any adjustments, changing acces-
sories, or storing the tool.
Such preventive safety
measures reduce the risk of starting the tool ac-
cidentally.
e)
Store idle tools out of reach of children and
other untrained persons.
Tools are dangerous in
the hands of untrained users.
f)
Maintain tools with care. Keep cutting tools
sharp and clean.
Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
g)
Check for misalignment or binding of moving
parts, breakage of parts and any other con-
dition that may affect the tool’s operation. If
damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained
tools.
h)
Use only accessories that are recommended by
the manufacturer for your model.
Accessories
that may be suitable for one tool may become
hazardous when used on another tool.
2.1.5 Service
a)
Tool service must be performed only by qual-
ified repair personnel.
Service or maintenance
performed by unqualified personnel could result
in a risk of injury.
b)
When servicing a tool, use only identical re-
placement parts. Follow instructions in the
Maintenance section of this manual.
Use of
unauthorized parts or failure to follow Mainte-
nance Instructions may create a risk of electric
shock or injury.
en
3
Printed: 07.07.2013 | Doc-Nr: PUB / 5069467 / 000 / 00
Summary of Contents for DAG 700-P
