![background image](http://html.mh-extra.com/html/hilti/dag-125-s/dag-125-s_operating-instructions-manual_2135604034.webp)
WARNING
The electric supply voltage must comply with the in-
formation given on the type identification plate on the
power tool. 230 V power tools may also be connected
to a 220 V supply.
WARNING
Always use the side handle with the power tool.
CAUTION
Use clamps or a vice to hold the workpiece securely.
WARNING
Cutting or grinding may cause splintering of the material.
Wear eye protection.
CAUTION
Breathing protection must be worn if the power tool
is used without a dust removal system for work that
creates dust.
WARNING
Avoid touching rotating parts. Switch the power tool
on only after bringing it into position at the workpiece.
Touching rotating parts, especially rotating insert tools,
may lead to injury.
CAUTION
The insert tool may get hot during use.
Wear protective
gloves when changing insert tools.
WARNING
Reduce the load on the power tool by avoiding tilt-
ing the disc in the kerf when cutting.
The disc may
otherwise break, or the power tool may kick back or stall.
CAUTION
Improve the blood circulation in your fingers by re-
laxing your hands and exercising your fingers during
breaks between working.
WARNING
Keep inflammable materials away from the working
area.
7.1 Switching on / off
7.1.1 Switching on
1. Plug the supply cord into the power outlet.
2. Press the rear section of the on / off switch.
3. Slide the on / off switch forward.
4. Lock the on / off switch.
7.1.2 Switching off
Press the rear section of the on / off switch. The on / off
switch jumps back to the off-position.
7.2 Restart interlock
NOTE
If the power tool is unplugged from the electric supply
while the on / off switch is locked in the on-position and
subsequently plugged back into the electric supply, it
will not restart. The switch lock must be released while
the power tool is disconnected from the electric supply
before the supply cord is again plugged into the power
outlet.
8 Care and maintenance
CAUTION
Disconnect the mains plug from the power outlet.
8.1 Care of the power tool
DANGER
Under extreme conditions, when used for working on
metal, conductive dust may accumulate inside the tool.
This may have an adverse effect on the tool’s protective
insulation.
Under such conditions, the tool should be
plugged into a ground fault circuit interrupter (RCD)
and use of a stationary dust removal system and
frequent cleaning of the tool’s cooling air slots is
recommended.
The outer casing of the power tool is made from impact-
resistant plastic. Sections of the grip are made from a
synthetic rubber material.
Never operate the power tool when the ventilation slots
are blocked. Clean the ventilation slots carefully using
a dry brush. Do not permit foreign objects to enter the
interior of the power tool. Clean the outside of the power
tool at regular intervals with a slightly damp cloth. Do
not use a spray, steam pressure cleaning equipment or
running water for cleaning. This may negatively affect the
electrical safety of the power tool. Always keep the grip
surfaces of the power tool free from oil and grease. Do
not use cleaning agents which contain silicone.
8.2 Maintenance
WARNING
Do not operate the power tool if parts are damaged
or when the controls do not function faultlessly. Have
the power tool repaired by Hilti Service.
WARNING
Repairs to the electrical section of the power tool may
be carried out only by trained electrical specialists.
Check all external parts of the power tool for damage
at regular intervals and check that all controls operate
faultlessly.
en
29
DCG 125-S / DAG 125-S / DAG 125-SE, Art. Nr.382617/A3, 05.03.2013
Printed: 08.07.2013 | Doc-Nr: PUB / 5069490 / 000 / 01
Summary of Contents for DAG 125-S
Page 2: ...Kwik Lock 6 1 Printed 08 07 2013 Doc Nr PUB 5069490 000 01 ...
Page 3: ...15 15 25 25 5 4 2 3 5 Printed 08 07 2013 Doc Nr PUB 5069490 000 01 ...
Page 4: ...3 2 1 1 2 2 6 4 3 2 5 1 7 8 6 5 4 6 7 3 1 9 Printed 08 07 2013 Doc Nr PUB 5069490 000 01 ...
Page 5: ...1 10 4 6 3 7 5 1 Printed 08 07 2013 Doc Nr PUB 5069490 000 01 ...