![background image](http://html1.mh-extra.com/html/hilti/bx-3/bx-3_original-operating-instructions_2135876029.webp)
English
23
WARNING
Risk of injury!
Pressing the nosepiece of the fastening tool against a part of the body may lead to
serious injury due to inadvertent firing and release of a fastener.
▶
Never press the nosepiece of the tool against your hand or any other part of the body.
1. Switch the fastening tool on. → page 22
2. Position the nose of the fastening tool at right angles to the working surface and then press it against the
surface, pushing the fastener guide in as far as it will go.
3. Drive the nail by pressing the safety trigger.
4. Lift the fastening tool completely away from the working surface after driving a fastener.
Note
The fastening tool switches itself off automatically if the fastener guide is pressed against the
working surface for longer than 6 seconds without a nail being driven. The fastening tool can be
switched on again by pressing the on/off button.
Note
If the fastening tool is not used for 6 minutes, spring tension is relaxed and the fastening tool
switches to stand-by mode automatically. The springs are automatically retensioned and the
fastening tool becomes ready for use again as soon as it is pressed against the working surface.
If the fastening tool is left in stand-by mode for longer than three hours it switches itself off
automatically. The fastening tool can be switched back on again by pressing the on/off button.
6.4 Switching Bluetooth off
▶
Press the on/off button for at least 5 seconds until the LED lights blue twice.
◁
No further data transfer is possible.
Note
If you are in a sensitive environment (e.g. a hospital) where use of Bluetooth is prohibited, Bluetooth
can be deactivated in this way.
6.5 Removing a nail when in magazine mode
1. Pull the nail pusher down until it engages.
2. Slide the nail downwards out of the magazine.
3. Hold the nail pusher securely and press the nail pusher release button.
4. Guide the nail pusher back to its original position.
6.6 Jammed nails
Individual nails may get stuck in the fastener guide. You can remove jammed nails from the fastener guide
with the aid of the X-NP drift punch set. Accessories are available from your
Hilti
Center or can be ordered
online at
www.hilti.com
.
WARNING
There is a risk of injury and damage to the fastening tool.
Use of unsuitable items instead of the
recommended genuine
Hilti
accessories may result in injury or damage to the fastening tool.
▶
To release a jammed nail, use only the recommended drift punch set.
CAUTION
Risk of injury by flying parts!
Triggering the tool (attempting to drive a fastener) when foreign objects
are present in the area around the fastener guide, or when a fastener is jammed in the fastener guide,
may lead to injury caused by flying objects or fragments.
▶
Never attempt to remedy tool malfunctions by continuing to trigger the tool.
6.6.1 Releasing jammed nails
1. Remove the fastener guide (see → page 21).
2. Fit the fastener guide into the supporting sleeve from the drift punch set.
Printed: 26.09.2017 | Doc-Nr: PUB / 5376263 / 000 / 00
Summary of Contents for BX 3
