background image

31

Observe the nationally and internationally applicable transport regulations when shipping batteries by

road, rail, sea or air.

Note

Ideally, the battery should be stored in a fully-charged state in a dry place that is as cool as

possible. Storing the battery in places subject to high ambient temperatures (e.g. at a window) has

an adverse effect on battery life and increases the rate of self-discharge.

If the battery no longer reaches full charge, it may have lost capacity due to aging or overstressing.

It is still possible to work with this battery. You should, however, soon replace the battery with a

new one.

8 Troubleshooting

If the trouble you are experiencing isn’t listed in this table or you are unable to remedy the problem by

yourself, please contact

Hilti

Service.

Trouble or fault

Possible cause

Action to be taken

The battery runs down more

quickly than usual.

Very low ambient temperature.

Allow the battery to warm up

slowly to room temperature.

The battery doesn’t engage

with an audible click.

The retaining lugs on the battery

are dirty.

Clean the retaining lugs and refit

the battery.

1 LED blinks.
The power tool doesn’t run.

Low battery.

Change the battery and charge

the empty battery.

The battery is too hot or too cold.

Allow the battery to cool down

or warm up slowly to room

temperature.

All 4 LEDs blink.
The power tool doesn’t run.

The tool has been overloaded.

Release the control switch and

then press it again. Then allow

the power tool to run under no

load for approx. 30 seconds.

The angle grinder or battery

gets very hot.

Electrical fault.

Switch the power tool off im-

mediately, remove the battery,

keep it under observation, allow

it to cool down and contact

Hilti

Service.

The tool does not achieve full

power.

A battery with inadequate capacity

was used.

Capacity: > 2.6 Ah

Use a battery with adequate

capacity.

The motor has no braking

effect.

Low battery.

Change the battery and charge

the empty battery.

The power tool was overloaded

briefly.

Release the control switch and

then press it again.

9 Disposal

WARNING

Risk of injury.

Hazards presented by improper disposal.

Improper disposal of the equipment may have the following consequences: The burning of plastic

components generates toxic fumes which may present a health hazard. Batteries may explode

if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or

environmental pollution. Careless disposal may permit unauthorized and improper use of the

equipment. This may result in serious personal injury, injury to third parties and pollution of the

environment.

Dispose of defective batteries right away. Keep them out of reach of children. Do not disassemble

or incinerate the batteries.

Batteries that have reached the end of their life must be disposed of in accordance with national

regulations or returned to

Hilti

.

Printed: 14.09.2015 | Doc-Nr: PUB / 5246581 / 000 / 00

Summary of Contents for AG 125-A36























Reviews: