background image

 

USING THE QUICK ARM 

The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to 
arm the security system in the AWAY mode by pressing the [

EXIT

] key.  The 

system can be quick armed in the STAY mode by pressing the [

STAY

] key.  This 

feature is used for ARMING ONLY, and will not disarm the security system.  This is 
ideal for a maid or baby sitter code, etc.

 

 
 

CHANGING MODES WHILE YOUR SYSTEM IS ARMED 

Step 1  Pressing the [

STAY

] key will turn on/off (toggle) a delay on Entry/Exit 

doors.  The “Instant” message will toggle on the LCD display. 

 
Step 2  (Optional, if programmed.)  Press the [

BYPASS

] key at this time to turn 

on/off (toggle) all designated interior zones.  If all interior zones are not 
bypassed, the 

stay light

 will extinguish. 

 
Step 3  (Optional, if programmed.)  When armed, pressing the [

EXIT

] key will start 

the Exit delay, enabling you to leave the building. 

 

IMPORTANT!

 

An alarm will be created if the “

Instant

” message is ON at this time and you re-enter 

the building.  You may re-initiate an entry/exit delay by pressing the [

STAY

] key 

again. The “

Instant

” message will disappear.  

 
 
DISARMING YOUR SYSTEM

 

When you enter the protected area through one of the designated Entry/Exit doors, 
the keypad control will sound a continuous tone for the duration of the entry delay 
time, or until you enter a valid code. 
 

Type code to 

Disarm

 

Step 1  Enter a valid user code. 
 
Step 2  The red 

armed light

 will go off and the tone will stop. The security system 

is now DISARMED.  If a valid code is not entered before the end of the 
entry delay, an alarm will occur.  

NOTE: 

 

If the red armed light is 

flashing during the entry delay, the alarm system has been activated 
in your absence. Leave the building immediately and call your alarm 
company and/or the police from a safe location. 

Hills LCD Keypad 

Summary of Contents for HILLS series





























Reviews: