manualshive.com logo in svg

HIKVISION DS-TCG227-A Series, User Manual, Page: 13 / 67

Share
Download
HIKVISION DS-TCG227-A Series User Manual Download Page 13

User Manual of DS-TCG227-A Series Entrance/Exit Capture Unit 

12 

 

 

Figure 2-4

 

Login Interface 

 

STRONG  PASSWORD  RECOMMENDED

–We  highly  recommend  you  create  a 

strong password of your own choosing (Using a minimum of 8 characters, including 

at  least  three  of  the  following  categories:  upper  case  letters,  lower  case  letters, 
numbers,  and  special  characters.)  in  order  to  increase  the  security  of  your  product. 

And we recommend you reset your password regularly, especially in the high security 

system, resetting the password monthly or weekly can better protect your product. 

4.

 

Install  the  plug-in  before  viewing  the  live  video  and  operating  the  capture 

unit. Please follow the installation prompts to install the plug-in. 

 

 

You may have to close the web browser to install the plug-in. Please reopen 

the web browser and log in again after installing the plug-in. 

 

You may receive “New version of plugin is detected. Update it?” Click 

OK 

to update to the latest version. 

2.6

 

Logout   

After login, click 

Logout

 to log out of the capture unit. 

2.7

 

Configure Setup Wizard 

Purpose: 

By default, the Setup Wizard starts once the device has loaded. You can configure the 

general parameters and adjust image. 

2.7.1

 

Configure General Parameters 

Purpose: 

You  can  configure  the  IP  address,  subnet  mask,  default  gateway,  capture  mode,  and 

Summary of Contents for DS-TCG227-A Series




































































Reviews:

No comments