background image

Keypad User Manual 

 

or dispose of it at designated collection points. For more information see: www.recyclethis.info. 

 

2006/66/EC (battery directive): This product contains a battery that cannot be 

disposed of as unsorted municipal waste in the European Union. See the product 

documentation for specific battery information. The battery is marked with this 

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury 

(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For 

more information see: www.recyclethis.info. 

Industry Canada ICES-003 Compliance

 

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the 

following two conditions:   

(1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired 

operation of the device. 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts 

de licence. L'exploitation est autorisée aux deux conditions suivantes : 

(1) l'appareil ne doit pas produire de brouillage, et 

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage 

est susceptible d'en compromettre le fonctionnement. 

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type 

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential 

radio interference to other users, the antenna type and its gain should be so chosen that the 

equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful 

communication. 

 

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut 

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur 

par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des 

autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope 

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une 

communication satisfaisante. 

 

 

 

Summary of Contents for DS-PK00-LCD series


















Reviews: