HIKVISION DS-KV8102-IM User Manual Download Page 22

Page: 22 / 87

Video Intercom Door Station

User Manual

5.1.2

Wall Mounting with Gang Box of DS-KV8X02-IM

Steps:

Take the gang box and screws from the packing box.

Chisel a hole in the wall for inserting the gang box. The size of the hole should be 90

(width) ×170 (length) × 38(depth) mm.

Insert the gang box into the hole and fix it with 4 PA4 screws, as shown in the figure

below.

PA4 Screws

Figure 5-2

Insert the Gang Box (DS-KV8X02-IM)

After fixing the gang box, install the door station into the gang box according to the

direction of the arrow, as shown in the figure below.

Figure 5-3

Insert the Door Station (DS-KV8X02-IM)

After inserting the door station into the gang box, pull the device downwards to hook

the door station with the gang box.

Secure the door station by inserting the fixing screw according to the direction of the

arrow of the figure below.

Summary of Contents for DS-KV8102-IM
























































































Search results

Summary of Contents for DS-KV8102-IM

Reviews:

Related manuals for DS-KV8102-IM

Brands by name

Popular brands

HIKVISION DS-KV8102-IM, User Manual

Search results

Summary of Contents for DS-KV8102-IM

Reviews:

Related manuals for DS-KV8102-IM

Brands by name

Popular brands