HIKVISION DS-7600NXI-K1 Series User Manual Download Page 93

Page: 93 / 103

Network Video Recorder User Manual

2. Click

3. Click Local Upgrade.
4. Select a backup device in Device Name.
5. Select the upgrade firmware.
6. Click Upgrade. Your device will reboot automatically.

7.4.2 Online Upgrade

Upgrade the device with the latest online firmware.

Before You Start
Ensure Hik-Connect is enabled and properly configured. Refer to Hik-Connect for details.

Steps
1. Click

at the upper-right corner.

2. Click

3. Go to Online Upgrade.
4. Download the latest firmware.

Auto Download

The will automatically check and download the latest firmware.

Test Upgrade

Click Test Upgrade to manually check and download the latest
firmware.

5. Upgrade your device if a new firmware version is available. The device will reboot automatically.

Summary of Contents for DS-7600NXI-K1 Series








































































































Search results

Summary of Contents for DS-7600NXI-K1 Series

Reviews:

Brands by name

Popular brands

HIKVISION DS-7600NXI-K1 Series, User Manual

Search results

Summary of Contents for DS-7600NXI-K1 Series

Reviews:

Brands by name

Popular brands