HIKVISION DS-7600NXI-K1 Series User Manual Download Page 89

Page: 89 / 103

Network Video Recorder User Manual

6.5.4 Configure Storage Mode

Configure HDD Quota

Each camera can be configured with an allocated quota for storing videos.

Steps

Note

This function is only available for certain models.

1. Go to Configuration → Record → Storage Mode.
2. Set Mode as Quota.
3. Select a camera to set quota in Camera.
4. Enter the storage capacity in Record Capacity.

Figure 6-34 Quota

Note

When the quota capacity is set to 0, all cameras will use the total capacity of HDD for videos and
pictures.

5. Click Apply.
6. Restart the video recorder to activate the new settings.

6.5.5 Advanced Settings

Steps
1. Go to Configuration → Record → Advanced.
2. Configure the parameters as your desire.

Overwrite

Summary of Contents for DS-7600NXI-K1 Series








































































































Search results

Summary of Contents for DS-7600NXI-K1 Series

Reviews:

Brands by name

Popular brands

HIKVISION DS-7600NXI-K1 Series, User Manual

Search results

Summary of Contents for DS-7600NXI-K1 Series

Reviews:

Brands by name

Popular brands