HIKVISION DS-7100HGHI-F1 User Manual Download

Page: 92 / 101

Chapter 7 Maintenance

7.1 Restore Default

Steps

1. Go to Maintenance .

2. Select the restoring type.

Simple Restore

Restore all parameters, except the network (including IP address, subnet mask, gateway,

MTU, NIC working mode, default route, server port, etc.) and user account parameters, to

the factory default settings.

Factory Defaults

Restore all parameters to the factory default settings.

Restore to Inactive

Restore the device to the inactive status, and leave all settings unchanged except restoring

user accounts.

3. Click Yes. The device will reboot automatically.

7.2 Search Log

The operation, alarm, exception and information of video recorder can be stored in logs, which can

be viewed and exported at any time.
Steps

1. Go to Maintenance → More .

2. Set the search conditions.

3. Click Search.

7.3 Upgrade

Warning

Do not shutdown or turn off the power during upgrade.

7.3.1 Local Upgrade

Before You Start

Store the upgrade firmware to a backup device, and connect it to your device.

Digital Video Recorder User Manual

Summary of Contents for DS-7100HGHI-F1






































































































Search results

Summary of Contents for DS-7100HGHI-F1

Reviews:

Related manuals for DS-7100HGHI-F1

Brands by name

Popular brands

HIKVISION DS-7100HGHI-F1, User Manual

Search results

Summary of Contents for DS-7100HGHI-F1

Reviews:

Related manuals for DS-7100HGHI-F1

Brands by name

Popular brands