HIKVISION DS-6700HQHI-SATA Quick Start Manual Download Page 3

DS-6700HQHI-SATA Series Encoder Quick Start Guide 

 

Regulatory Information 

FCC Information 

FCC compliance: 

This equipment has been tested and found to comply with the limits for a Class A digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference  when  the  equipment  is  operated  in  a  commercial  environment.  This  equipment  generates,  uses,  and 

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may 

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to 

cause harmful interference in which case the user will be required to correct the interference at his own expense. 

 

FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1. This device may not cause harmful interference. 

2. This device must accept any interference received, including interference that may cause undesired operation. 

EU Conformity Statement 

This  product  and  -  if  applicable  -  the  supplied  accessories  too  are  marked  with  "CE"  and  comply 

therefore  with  the  applicable  harmonized  European  standards  listed  under  the  EMC  Directive 

2004/108/EC, the RoHS Directive 2011/65/EU. 

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted 

municipal  waste  in  the  European  Union.  For  proper  recycling,  return  this  product  to  your  local 

supplier  upon  the  purchase  of  equivalent  new  equipment,  or  dispose  of  it  at  designated  collection 

points. For more information see: 

www.recyclethis.info

 

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted 

municipal  waste  in  the  European  Union.  See  the  product  documentation  for  specific  battery 

information.  The  battery  is  marked  with  this  symbol,  which  may  include  lettering  to  indicate 

cadmium  (Cd),  lead  (Pb),  or  mercury  (Hg).  For  proper  recycling,  return  the  battery  to  your  supplier  or  to  a 

designated collection point. For more information see: 

www.recyclethis.info 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements. 

Summary of Contents for DS-6700HQHI-SATA























Reviews: