HIKVISION 114-029 User Manual Download Page 174

Page: 174 / 190

Network Camera User Manual

173

The toolbar on the bottom of Playback interface can be used to control playing

process.

Playback Toolbar

Table 12-1

Description of the buttons

Button

Operation

Button

Operation

Play

Capture a picture

Pause

Start/Stop clipping video

files

Stop

Audio on and adjust

volume/Mute

Speed down

Download

Speed up

Playback by frame

Enable/Disable

digital zoom

Note:

You can choose the file paths locally for downloaded playback video files and

pictures in Local Configuration interface.

You can also input the time and click

to locate the playback point in the

Set

playback time

field. You can also click

to zoom out/in the progress bar.

Set Playback Time

Progress Bar

The different colors of the video on the progress bar stand for the different video

types.

Video Types

Summary of Contents for 114-029































































































































































































Search results

Summary of Contents for 114-029

Reviews:

HIKVISION 114-029, User Manual, Page: 174 / 190

Search results

Summary of Contents for 114-029

Reviews: