HIKVISION 114-029 User Manual Download Page 142

Page: 142 / 190

Network Camera User Manual

141

be more accurate if the camera calibration is configured.

Steps:

Check the checkbox of

Camera Calibration

to enable this function.

Select the calibration mode as Input Basic Data or Draw on Live View Video.

Input Basic Data

: Input the mounting height, viewing angle, and horizon

ratio of the camera manually.

Draw on Live View Video

: Click

Draw Verification Line (Horizontal) /

(Vertical)

to draw a horizontal/vertical line in the live view, and input the

actual length in Real Length field. With the drawn reference lines and their

real length, the camera can conclude other objects appear in the live view.

Click the Horizontal Verify

Vertical Verify

button to draw a

horizontal / vertical line on the live video, and click the

Start Verifying

button to calculate the line length. Compare the calculated line length to the

actual length to verify the calibration information you set.

Note:

If the live view is stopped, the camera calibration is invalid.

Draw on Live View Window

Summary of Contents for 114-029































































































































































































Search results

Summary of Contents for 114-029

Reviews:

HIKVISION 114-029, User Manual, Page: 142 / 190

Search results

Summary of Contents for 114-029

Reviews: