HIKOKI G18MR Handling Instructions Manual Download Page 6

6

English

b)  The grinding surface of centre depressed wheels 

must be mounted below the plane of the guard lip. 

 

An improperly mounted wheel that projects through the 

plane of the guard lip cannot be adequately protected.

c)  The guard must be securely attached to the power 

tool and positioned for maximum safety, so the 

least amount of wheel is exposed towards the 

operator.

  The guard helps to protect the operator from broken 

wheel fragments, accidental contact with wheel and 

sparks that could ignite clothing.

d)  Wheels  must  be  used  only  for  recommended 

applications. For example: do not grind with the 

side of cut-o

  wheel. 

 Abrasive 

cut-o

  wheels are intended for peripheral 

grinding, side forces applied to these wheels may 

cause them to shatter.

e)  Always use undamaged wheel 

fl

 anges that are of 

correct size and shape for your selected wheel. 

 Proper 

wheel 

fl

 anges support the wheel thus reducing 

the possibility of wheel breakage. Flanges for cut-o

  

wheels may be di

 erent from grinding wheel 

fl

 anges. 

f)  Do not use worn down wheels from larger power 

tools. 

 

Wheel intended for larger power tool is not suitable for 

the higher speed of a smaller tool and may burst.

ADDITIONAL SAFETY WARNINGS SPECIFIC 

FOR ABRASIVE CUTTING-OFF OPERATIONS

a)  Do not “jam” the cut-o

  wheel or apply excessive 

pressure. Do not attempt to make an excessive 

depth of cut. 

  Overstressing the wheel increases the loading and 

susceptibility to twisting or binding of the wheel in the 

cut and the possibility of kickback or wheel breakage.

b)  Do not position your body in line with and behind 

the rotating wheel. 

  When the wheel, at the point of operation, is moving 

away from your body, the possible kickback may propel 

the spinning wheel and the power tool directly at you.

c)  When wheel is binding or when interrupting a cut 

for any reason, switch o

  the power tool and hold 

the power tool motionless until the wheel comes to 

a complete stop. Never attempt to remove the cut-

o

  wheel from the cut while the wheel is in motion 

otherwise kickback may occur. 

  Investigate and take corrective action to eliminate the 

cause of wheel binding.

d) Do not restart the cutting operation in the 

workpiece. Let the wheel reach full speed and 

carefully reenter the cut. 

  The wheel may bind, walk up or kickback if the power 

tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to 

minimize the risk of wheel pinching and kickback.

  Large workpieces tend to sag under their own weight. 

Supports must be placed under the workpiece near the 

line of cut and near the edge of the workpiece on both 

sides of the wheel.

f)  Use extra caution when making a “pocket cut” into 

existing walls or other blind areas.

  The protruding wheel may cut gas or water pipes, 

electrical wiring or objects that can cause kickback.

PRECAUTIONS ON USING DISC GRINDER

1. Never operate these power tools without Wheel 

Guards.

2.  Check that speed marked on the wheel is equal to or 

greater than the rated speed of the grinder.

  Use only depressed center wheels rated at 80 m/s or 

more.

3.  Ensure that the wheel dimensions are compatible with 

the grinder and that the wheel 

fi

 ts the spindle.

4.  Abrasive wheels shall be stored and handled with care 

in accordance with manufacturer’s instructions.

5.  Inspect the depressed center wheel before use, do not 

use chipped, cracked or otherwise defective products.

6.  Always hold the body handle and side handle of the 

power tool 

fi

 rmly. Otherwise the counterforce produced 

may result in inaccurate and even dangerous operation.

7.  Do not use cutting-o

  wheels for side grinding.

8.  Do not use of separate reducing bushings or adapters 

to adapt large hole abrasive wheels.

9.  The wheel continues to rotate after the tool is switched 

o

 .

SPECIFICATIONS

Model

G18MR

G23MR

Voltage (by areas)

*1

(110 V, 220 V, 230 V, 240 V) 

Input

*1

2400 W

No-load speed

8500 min

-1

6600 min

-1

Wheel

Outer dia. 

180 mm

230 mm

Inner dia.

22.23 mm

Peripheral speed

80 m/s

Weight

*2

5.4 kg

*1  Be sure to check the nameplate on product as it is subject to change by areas. 

*2  Weight: Only main body

000Book̲G18MR.indb   6

000Book̲G18MR.indb   6

2018/03/14   16:29:38

2018/03/14   16:29:38

Summary of Contents for G18MR





























Reviews: