background image

Dichroic Theatre™

 

User Manual

i

Dichroic Theatre Series

User Manual

© High End Systems, Inc. 2003, All Rights Reserved

Information and specifications in this document are subject to change without notice. 
High End Systems, Inc. assumes no responsibility or liability for any errors or 
inaccuracies that may appear in this manual. 

Trademarks used in this text:

 High End Systems, WholeHog III, and Hog are registered 

trademarks; and ColorCommand, ColorMerge, ColorPower, the High End Systems globe 
logo and the Hog logo are trademarks of High End Systems, Inc. or High End Systems 
Europe Ltd. ETC. Source Four is a trademark of Electronic Theatre Controls Inc. High 
End Systems has no relationship or affiliation of any nature with Electronic Theatre 
Controls and High End Systems is fully responsible for the ColorMerge, ColorPower, and 
ColorCommand products. ColorMerge - patents pending. ColorCommand - covered by 
patents 6,502,961, 6,142,652, and 6,048,081. Belden is a registered trademark of Belden, 
Inc. Philips is a registered trademark of Philips Lighting Company. ETL and C-ETL are 
registered trademarks of Intertek Testing Services. 

Other trademarks and trade names may be used in this document to refer to either the 
entities claiming the marks and names or their products. High End Systems disclaims any 
proprietary interest in trademarks and trade names owned by others.

Dichroic Theatre

TM

 User Manual

P/N 60600229 Version 2.0, December 2003

P/N 65020001 (ColorPower)
P/N 64010001 (ColorCommand

TM

)

P/N 59010001 (ColorMerge

TM

)

Summary of Contents for Dichroic Theatre Series





























































Reviews: