Hi-Target V90 Plus Getting Started Download Page 7

Page: 7 / 128

Products Introductions

Smart Application

◇

Offers tilt survey with a maximum tilt angle of 30 degrees.

◇

Supports electronic bubble calibration

◇

The internal NFC module makes Bluetooth communication quick and easy.

◇

Intelligent voice assistance guides field operations. Voice can be DIY.

◇

Standard Rinex data and HI-TARGET raw data recorded simultaneously.

Optional Transceiver UHF Radio

◇

The transceiver UHF radio enables switchable working modes between base and rover.

◇

Three types of internal UHF radio provide different frequencies based on users requirements. The

Pacific Crest TrimTalk© internal UHF radio is compatible with other radios.

Multi-network Connection

◇

Supports WIFI

Powerful Battery

◇

Rugged Design

◇

IP67 dustproof and waterproof

◇

Able to survive a 3-meter natural fall onto concrete

Summary of Contents for V90 Plus
































































































































Search results

Summary of Contents for V90 Plus

Reviews:

Related manuals for V90 Plus

Brands by name

Popular brands

Hi-Target V90 Plus, Getting Started

Search results

Summary of Contents for V90 Plus

Reviews:

Related manuals for V90 Plus

Brands by name

Popular brands