Hi-flying HF-LPB User Manual Download Page 25

Page: 25 / 59

HF-LPB Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd

www.hi-flying.com

- 25 -

2.8. Parameters Configuration

HF-LPB module supports two methods to configuration parameters

: Web Accessing

and

AT+instruction set.

Web accessing means users can configure parameters through Web browser. When HF-LPB module

connected to wireless network, parameters configuration is done on a PC connected to the same

wireless network.

AT+instruction set configuration means user configure parameters through serial interface command.

Refer to “AT+instruction set” chapter for more detail.

2.9. Firmware Update

HF-LPB module supports two on-line upgrade methods:

Webpage Wi-Fi Upgrade

Remote

Upgrade

Webpaged based Wi-Fiupgrade,please refer to 3.1.8 firmware upgrade page , user can upload

firmware file from PC to HF-LPB.

Remote upgrade: TBD

Notes:

please contact with high-flying technical people before upgrade firmware, or maybe damage

the module and can’t work again.

2.10. GPIO Function

HF-LPB module can provide maximum 12 GPIO pins, which include 2 A/D analog input pins, 3 PWM

control pins, 2 Pin sleep control pins, 1 WPS pin, 1 RTC pin, 1 USB 5V control pin, and 2 general

GPIO pin. All these pins can be customized as GPIO pins if these functions are not required. As GPIO

functional pin, user devices can read/write GPIO pins status through AT+instruction set.

Table 8 HF-LPB GPIO Pin Mapping Table

When module works at GPIO mode, PC and other equipts can setup connection (TCP/UDP) through

WiFi, then read/write GPIO information through command.

GPIO

Configured Function

Describtion

Default Setting

Type

GPIO7 Sleep_RQ

Wakeup/Sleep

Sleep_RQ

I,PD

GPIO8

Sleep_ON

GPIO11 A/D Input 1

A/D

GPIO11 I/O,PD

GPIO12 A/D Input 2

GPIO12

I/O,PD

GPIO13 RTC Input 2

RTC

GPIO13 I,PD

GPIO16 USB 5V Track

USB

GPIO16

I/O

GPIO20 GPIO

GPIO

GPIO20 I/O

GPIO23 PWM Dif. Out+

PWM

GPIO23

GPIO24 PWM Dif. Out-

GPIO24

GPIO26 GPIO

GPIO

GPIO26 I/O

GPIO35 WPS

Input

WPS

GPIO35

I/O,PD

GPIO46 PWM Fault Input

PWM

GPIO46

I/O

Summary of Contents for HF-LPB




























































Search results

Summary of Contents for HF-LPB

Reviews:

Related manuals for HF-LPB

Brands by name

Popular brands

Hi-flying HF-LPB, User Manual

Search results

Summary of Contents for HF-LPB

Reviews:

Related manuals for HF-LPB

Brands by name

Popular brands