Hi-flying HF-LPB User Manual Download Page 58

Page: 58 / 59

HF-LPB Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd

www.hi-flying.com

- 58 -

The user manual or instruction manual for an intentional or unintentional radiator shall caution the

user that changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment. In cases where the manual is provided

only in a form other than paper, such as on a computer disk or over the Internet, the information

required by this section may be included in the manual in that alternative form, provided the user

can reasonably be expected to have the capability to access information in that form.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

1.4 FCC RF exposure requirements

1. Radiated transmit power must be equal to or lower than that specified in the FCC Grant of

Equipment Authorization for FCC ID:

AZY-HF-LPB

2. To comply with FCC regulations limiting both maximum RF output power and human exposure to

RF radiation, maximum antenna gain (including cable loss) must not exceed:

❒

802.11b band < 0.8 dBi

❒

802.11g band < 0.8 dBi

❒

802.11n band <0.8 dBi

3. This module must not transmit simultaneously with any other antenna or transmitter.

4. To ensure compliance with all non-transmitter functions the host manufacturer is

responsible for ensuring compliance with the module(s) installed and fully operational. For

example, if a host was previously authorized as an unintentional radiator under the

Declaration of Conformity procedure without a transmitter certified module and a module is

added, the host manufacturer is responsible for ensuring that the after the module is installed

and operational the host continues to be compliant with the Part 15B unintentional radiator

requirements.

Summary of Contents for HF-LPB




























































Search results

Summary of Contents for HF-LPB

Reviews:

Related manuals for HF-LPB

Brands by name

Popular brands

Hi-flying HF-LPB, User Manual

Search results

Summary of Contents for HF-LPB

Reviews:

Related manuals for HF-LPB

Brands by name

Popular brands