background image

 

IMPORTANT DECLARATIONS 

 

Copyright © 2018 Heyuan Intelligence Technology Co., Ltd All Rights Reserved 
 
This manual may not be reproduced, copied, transmitted or transcribed in whole or in part by any 
means  without  the  expressed  written  permission  of  Heyuan. Any  shall  be  investigated  for  legal 
responsibility in violation of copyright or other intellectual property rights of the Company. We check 
the user manual’s contents regularly and will make necessary amendments in next version. Welcome 
to give advice for some unexpected errors. The rights of upgrading without notice are reserved. 
 
Please read this manual carefully before the product is operated. And once you start operating the 
meter, you’ll be considered to have read this manual and accept all our terms. Heyuan shall not be 
responsible  or  liable  for  any  damages  or  injuries  caused  by  improper  meter  installation  and/or 
operation. 
 
Attention: the following symbols in this manual refer to meanings as follows 

   

Electric Shock Symbol: Carries information about procedures which must be followed 

to reduce the risk of electric shock and danger to personal health   

   

Safety Alert Symbol: Carries information about circumstances which if not considered 

may result in injury or death 
 

The meter must be installed and operated by one who has experience with high-voltage devices or 
has qualifications. Please connect the meter to correct voltage before operating the meter. Please 
install and use the meter according to the user manual. Heyuan shall not be responsible or liable for 
any damages or injuries caused without following the instructions in the user manual. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for DZ81-MS3UI7C













Reviews: