Hewlett Packard Enterprise HPE FlexNetwork MSR958 Installation Manual Download Page 10 | Manualshive

Page: 10 / 33

Hewlett Packard Enterprise HPE FlexNetwork MSR958 Installation Manual Download Page 10

6

Installing the router

WARNING!

To avoid injury, do not touch bare wires, terminals, or parts with high-voltage hazard signs.

IMPORTANT:

•

The barcode on the router chassis contains product information that must be provided to local

sales agent when you return a faulty router for repair.

•

Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want

to open the chassis, contact Hewlett Packard Enterprise for permission. Otherwise, Hewlett
Packard Enterprise shall not be liable for any consequence.

Installation prerequisites

•

You have read "

Preparing for installation

•

All requirements in "

Preparing for installation

Installation flowchart

You can install the router on a workbench or in a rack. Determine the installation location as
required. Follow the installation flowchart shown in

to install the router.

«
...
8
9
10
11
12
...
»

Summary of Contents for HPE FlexNetwork MSR958


































Reviews:

No comments