Operation:
1.
Insert the power line to the traditional AC220-240V and 16A socket directly and then press down the main power switch of the rear plate, the
light on the main power switch and the power indicator light on the power switch button (ON/OFF) above the front control panel displayed as
red.
2.
Then press down the power switch button (ON/OFF) on remote control or on the front control panel, the
“M
ODE
” on the control panel will
display “A
UTO
”
and the light in red, the
“
ROOM TEMP
”
show indoor ambient temperature and the
“
SET TEMP
”
shows your desired
temperature.
3.
You can press the
“
MODE
”
button to choose
“
MAX
”
mode or
“
AUTO & Energy-saving
”
mode you want.
4.
If the heater is not used, it should be turned off by pressing the power switch button (ON/OFF) on the remote control or front control panel
first. Now the fan will continue running 3 minutes to blow out the rest of heat from the internal, to cool down the heater, prevent over-heating
and make the heater more durable. 3 minutes later, the fan will stop running; you can cut off the main power supply switch of rear plate and
pull off the plug.
In any time, do not cut off the main power supply switch of rear plate or pull off the plug directly, it will cause over-heating and reduce the
lifetime of the heater.
Tips:
The heaters are designed to operate for maximum efficiency from 16 to 22
℃
range. Due to the soft heat concept, a temperature of 20
℃
will
feel as though it were 22
℃
, this is due to the heat mixing evenly with humidity of 40% for “head-to-toe” comfort.
Notice:
that the temperature displayed on the control panel of the heater is unnecessarily consistent with wall-mounted thermostat, thermometer
or other internal temperature displays, since the heater is placed close to the ground, the temperature sensor is inside of the back of the heater,
which will make the recorded temperature lower or higher. However, it does not mean that the actual temperature of the house is that low or the
heater does not send out heat. If the temperature displayed by the heater is about 4
℃
-5
℃
different from the temperature of other temperature
readers, it is completely normal.
Tips:
1.
Do not put the heater in a place with strong air ventilation.
2.
Make the air outlet in the middle of the house. Do not place it against a firm building like wall. If the place is relatively big, put the heater in the
center.
3.
The set temperature of the heater ranges from 18
℃
to 30
℃
. It is mainly because that is comfortable room temperature range.
4.
Before use of heater, other heating and exhaust systems shall be turned off to make sure the heater works in an independent place.
5.
It is not suggested to use heater aside the non-insulating metal or concrete wall. The indoor concrete floor shall be converted as non-insulating.
6.
If the heater is dirt or with dust, it shall be constantly cleaned to assure the working efficiency of heater.
Washable lifetime filter system:
THE Heaters come equipped with a washable lifetime filter on the rear of the unit that is easy to clean.
IMPORTANT INFORMATION: If you have allergies and/or are sensitive to dust, you will want to use this filter. When choosing to use the filter, it
must be cleaned daily; a clogged filter will cause the heater to not work to its full capacity.
Using the heater with the dust filter attached is an optional feature. Operating the heater without the filter will in no way harm or alter the
operation of the heater. If you are not sensitive to dust or do not want to clean the filter daily, please remove it from the back of unit and use your
heater without it.
To clean the filter:
1)
Press the tab on the top of the filter to release the filter and pull it straight out.
2)
Run warm tap water over the filter, the opposite direction of air flow, until water runs clear. The filter might excrete some filtered residue, so be
cautious not to drip on any stainable surfaces such as carpeting. You can also soak the filter in water mixed with a small amount of mild dish soap
(do not forget to rinse with water after soaking filter).
