3)
Shake the filter over a sink until excess water is removed and allow it to drip dry completely before reinstalling. DO NOT force the filter to dry
using any alternative methods.
4)
Reinstall the filter to the rear of the unit by positioning the filter back in place.
WARNING:
ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE SHOULD ONLY BE PERFORMED BY AN AUTHORIZED
SERVICE REPRESENTATIVE
To assure maximum performance of the Heater, please note the following recommendations:
1)
For best results, do not locate the heater in an area with a high rate of air filtration and movement as the warm air will be exhausted.
2)
Try placing the heater near a warmer inside wall and direct the output toward a cooler outside wall. The cooler outside wall will tend to draw
the generated heat toward itself, which will allow for more efficient heating.
3)
Placing the heater next to a cold air return will draw the heat away from area to be heated. Try closing or covering the cold air return. This will
allow for more efficient heating. Experiment with the placement of the heater to see what works best for you.
4)
To ensure maximum efficiency, a 40% (minimum) relative humidity should be maintained in the heated environment.
5)
The heaters are designed to operate for maximum efficiency from 16 to 22
℃
range. Due to the soft heat concept, a temperature of 20
℃
will
feel as though it were 22
℃
. This is due to the heat mixing evenly with humidity for “head-to-toe” comfort.
6)
When the heater is placed in an isolated area, i.e. basement or recreation area, the delivery registers and air return grills of the existing system
should be closed in that area if possible.
7)
In rooms with large areas of bare concrete, try placing the heater a few feet above the floor. Make sure the heater is secure and will not fall. This
will allow for more efficient heating since concrete acts as a heat sink and will tend to draw the heat its direction.
8)
Try lowering your central heating system to a lower temperature and placing the heater in the area you spend most of your time. Now set the
heater to your comfort level. After all, there is no point to heating multiple rooms to 20+ degrees when they are not in use.
9)
When heating larger areas, place the heater in a central location. If a ceiling fan is nearby, try using it at the same time to help distribute the heat
evenly.
Our suggestion gives it a try and see what works best for you.
10)
If used in an extremely dirty or dusty area, the filter must be cleaned more frequently as it can clog and cause the heater to stop working.
11)
The heater grill is hot when in use. To avoid burns, do not let bare skin touch hot surface. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least three feet from the front of the heater and keep them away from the sides and rear.
12)
Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
13)
To disconnect heater, press power button to “off,” then remove plug from outlet.
14)
Always unplug heater when not in use.
Maintenance and Storage:
Before the maintenance of heater, the power supply shall be pulled off first. The wooden case shall be wiped by using water and wet rag. The
heater is fitted with a cleanable filter screen. The filter screen shall be cleaned as scheduled to assure the use of the heater to a maximal extent.
After the filter screen is removed, pour the warm water I the filter screen for cleaning. Spin dry the water in the filter screen and reinstall it. (Note:
mild soap can better clean the filter screen). If the heater is not used anymore, it may be stored. Make sure the power supply is turned off and the
power line is pulled off. Wrap the power line and cover the heater to retain dust. Also, the heater may be packed to the original status before
disassembly. Store the heater in a dry and dust-free environment. (Note: before storage, the filter screen shall be cleaned to prepare for the next
use.)
Failure Analysis:
1. Problems:
A. The heating equipment is damaged.
B. The control panel does not react, and the temperature is displayed as 30
℃
, or there is a burning smell.
C. The power line is damaged.
Solution:
Contact with the supplier immediately. It is forbidden to use heater to prevent electric shock, fire, etc..
