background image

2.3.  Instructions Before Installation

2.4.  TF Card Installation

If you need to use an TF card to store video, pictures and other data, please 
install the TF card before installing the device. If you don't need to use TF 
card to store data, please skip this chapter. 

After installing the TF card in the IPC, you need to install it 
according to the method before disassembly, otherwise it 
will affect the airtightness of the camera and thus affect 
the normal use of the device.

Warning

The wall to be installed should have a certain thickness and can withstand at 
least 4 times the weight of the camera and mounting accessories.

If  the  device  is  installed  on  a  concrete  wall  or  ceiling,  you  need  to  install 
expansion screws before installing the bracket. (Please note that 

the  holes  of  the  expansion  screws  must  be  consistent  with  the  mounting 
bracket) 

If  the  device  is  installed  on  a  wooden  wall,  the  bracket  can  be  directly 
installed on the wall with self-tapping screws.

When you pick up the camera, do not directly pull the cable at the rear of 
the camera. Otherwise, it may damage the waterproof performance of the 
camera or cause circuit problems.

Before installation, please check whether the equipment in the packing box 
is intact and all accessories are complete.

Summary of Contents for OWL256

















Reviews: