Heatrae Sadia Multipoint 30H Fitting Instructions Manual Download Page 14

14

10.1

 Fault finding

Disconnect the electrical supply before removing the 

terminal cover. It is recommended that any service 

operations on the product are carried out by a 

competent person.

10.  Troubleshooting

WARNING

Do not tamper with any of the safety valves 

or controls supplied with the cylinder as 

this will invalidate any warranty.

 

Symptom

Possible cause

Remedy

Water not heating

A. Electrical supply fault

A. Check electrical supply

B. Thermal cut-out tripped

B. Check cut-out, if operated reset and check 

thermostat operation. If necessary replace 

thermostat/thermal cut-out (see wiring diagram)

C. Thermostat fault

C. Check thermostat operation. Replace if 

necessary

Discharge of water 

from pressure relief 

valve (continuously)

Excessive mains water pressure

Fit Pressure reducing valve Pack U1 and U2 

(see important installation points)

Discharge of water 

from Pressure relief 

valve  (intermittently)                                                                                        

A. Expansion in mains not 

possible

A. Fit pack U2 (see important installation points)

B. Mains pressure exceeds 0.41 

MPa (4.1 bar)

B. Fit packs U1 and U2

C. Pack U1 fitted without pack U2

C. Fit pack U2 when using pack U1

D. Pressure relief valve fault

D. Replace pressure relief valve

E. Loss of pressure from 

expansion vessel

E. Check and if necessary re-charge Expansion 

vessel pre-charge pressure (see section 9)

Discharge of water 

from Temperature / 

pressure relief and/

or water/steam from 

pressure relief valve

Thermostat and thermal cut-out 

fault

Replace thermostats and thermal cut-outs

No water flow

A. Inlet vales incorrectly fitted

A. Check all vales are correctly installed in 

accordance with flow direction arrows

B. Mains water supply not turned 

on

B. Check mains water supply is on

C. Blockage in mains water 

supply

C. Check for obstructions. If pack U1 is fitted 

check the strainer is not blocked 

'Milky water'

Oxygenated water

Water from a pressurised system releases 

oxygen bubbles when flowing. The milkiness will 

disappear after a short while

Summary of Contents for Multipoint 30H





















Reviews: