background image

Model:

 

UH6

       Zones 

1…6 

(Inputs)

Zone inputs are clearly marked at the top of the circuit board;

L     = Live supply to thermostat.

       = Timed switch live to thermostat, activated by the      input from the time clock.

N    = Neutral supply to thermostat.

S/L = 230v switch live from thermostat, this activates the corresponding zone output.

    Time 

Clock 

Input

L  = Live supply

E  = Earth

N = Neutral supply

    = Switch live input from time clock, this enables

the       terminal on the thermostat connections.

 

 

 

 

 

 

     Zones 1…6 (Actuator/Valve Outputs)

Zones outputs are clearly marked

L   = Live out to actuator or valve

N   = Neutral to actuator or valve

There are four live (L) connections and four neutral (N) connections.

The L & N connections correspond to the thermostat zone wired in at the top of the UH6.

When there’s a demand from this zone, all four sets of L & N connections are activated,

the corresponding zone LED will light up.

            UFH 

Pump

This output is used for an underfloor heating manifold pump.

Connections are clearly marked;

N = Neutral

E = Earth

L = Live

When an under-floor heating zone sends a call for heat to the UH6, the live & neutral output will supply 230v

to the  manifold pump. It is recommended that this is fed through a high limit switch placed on the heating

manifold,  to protect against mechanical failure of the manifolds temperature control.

         UFH/RAD 

(Zone 

6)

This switch determines if zone 6 activates the HEAT & UFH Pump terminals as well

as the actuator/valve output, when there’s a demand.

UFH Zone

HEAT & UFH Pump Enabled

Radiator Zone

HEAT & UFH Pump NOT Enabled

     UFH         RAD

 

                 

     UFH          RAD

 

                 

4

Summary of Contents for UH6





















Reviews: