background image

01/04

31818 Rev J

15

ODYSSEY SERIES FIREPLACE WITH GAS LOG SET

F. STEP-BY-STEP INSTALLATION OF FIREPLACE SYSTEM

WARNING!

Before starting, do the following:

1. Wear gloves and safety glasses for protection.
2. Keep hand tools in good condition. Sharpen cutting edges and make sure tool handles are secure.
3. Always maintain the minimum air space required to the enclosure to prevent fire.

1. Position the Fireplace

This fireplace may be placed on either a combustible or

noncombustible  continuous  surface.  Follow  the

instructions for framing on pages 9-12. 

Be sure to provide

the minimum 3/4” air clearance at the sides and back

of the fireplace assembly.

2. Place the Protective Metal Hearth Strips

Included with your fireplace you will find two metal hearth

strips  measuring  approximately  4”  x  26”.  These  strips

are used to provide added protection where the fireplace

and hearth extension meet.

Slide the metal strips two inches under the front edge of

the  fireplace.  The  individual  pieces  must  overlap  each

other by one inch in the middle of the fireplace to provide

continuous coverage of the floor. See Figure 10. These

metal strips should extend from the front and sides of the

fireplace opening by 2”.

3. Level the Fireplace

Level  the  fireplace  side-to-side  and  front-to-back.  Shim

with  noncombustible  material,  such  as  sheet  metal,  as

necessary.

Important

: To ensure proper fit of the glass doors, check

the  fireplace  opening  to  ensure  it  is  square.  Measure

diagonal distances of the opening to make sure they are

equal. If they do not equal, continue to shim the fireplace

until  those  diagonals  correspond.

Secure the fireplace by utilizing the nailing flanges located

on either side of the fireplace to the vertical framing.

Figure 10

Positioning the Metal Strips

WARNING!

Carefully follow the instructions for assem-

bly of the pipe and other parts needed to

install this fireplace system. Failure to do

so may result in a fire, especially if com-

bustibles are too close to the fireplace or

chimney and air spaces are blocked pre-

venting the free movement of cooling air.

Summary of Contents for ODYSSEY ODY42

































Reviews: