Heatilator Heatilator CI60 Owner'S Manual Download

Page: 34 / 46

Heatilator • CI60 • 4013-031 Rev M • 10/06

A. Disposal of Ashes

Ashes should be placed in a metal container with a tight-

ting lid. The closed container of ashes should be placed on
a noncombustible

oor or on the ground, well away from all

combustible materials, pending

nal disposal. If the ashes

are disposed of by burial in soil or otherwise locally dis-
persed, they should be retained in the closed container until
all embers have thoroughly cooled.

B. Chimney Inspection/Cleaning

Inspect the chimney internally for obstructions and construc-
tion damage. Flue pipe joints and seams must be continu-
ous and mechanically tight.

The chimney should be inspected once every two months
during the heating season.

If creosote has accumulated, it should be removed to reduce
the risk of a chimney

re.

Refer to Figure 11.1 to remove/reinstall termination caps.

Chimney

Remove 4 screws
and lift top pan off.

Cap

Slip
Section

ST475

Square Termination Cap

Cap

Top Cover

TR442, TR444

Round Termination Cap

Remove screws
and lift top cover.

Figure 11.1 Chimney & Termination Cap Cleaning

Fire Risk

Disposal of ashes

• Ashes should be placed in metal container with tight

tting lid.

• Do not place metal container on combustible

surface.

• Ashes should be retained in closed container until all

embers have thoroughly cooled.

WARNING

Fire Risk

Prevent creosote buildup

•

Inspect chimney once every two months during heating
season.

• Remove creosote to reduce risk of chimney

re.

• Ignited creosote is extremely HOT.

WARNING

C. Firebox Refractory

Check

rebox refractory for excessive cracks or gaps. If

cracks exceed 1/4 in. (6 mm) in width the refractory should
be replaced. See Section 12 for replacement information.

Fire Risk

• Inspect

replace refractory annually.

Crumbling, deteriorated refractory can allow
overheating of surrounding materials.

WARNING

Note:

As you use the

replace, expansion and contraction

will cause minor cracking of the refractory. This is normal,
unavoidable, and will not affect the performance of the

replace. If the cracks become large enough that the metal

behind the refractory is exposed or large pieces fall out, the
panels should be replaced.

Maintenance and Servicing the Fireplace

Summary of Contents for Heatilator CI60















































Search results

Summary of Contents for Heatilator CI60

Reviews:

Related manuals for Heatilator CI60

Brands by name

Popular brands

Heatilator Heatilator CI60, Owner'S Manual

Search results

Summary of Contents for Heatilator CI60

Reviews:

Related manuals for Heatilator CI60

Brands by name

Popular brands