Heath Zenith SL-5412 Owner'S Manual Download Page 4

4

598-1265-01

SYMPTOM

Lights will not come 

on.

Lights  come  on   

in daylight.

Lights  come  on 

for  no  apparent 

reason.

POSSIBLE CAUSE

1.  Light switch is turned off.

2.  F l o o d   l i g h t   i s   l o o s e   o r   

burned out.

3.  Fuse is blown or circuit breaker 

is turned off.

4.  Daylight turn-off is in effect 

(re-

check after dark)

.

5.  Incorrect circuit wiring, if this is a 

new installation.

6.  Re-aim the sensor to cover de-

sired area.

1.  Light control may be installed in 

a relatively dark location.

2.  Light  control  is  in  Test. 

 

(Set  control  switch  to  an   

ON-TIME position)

.

1.  Light  control  may  be  sensing 

small animals or automobile traf-

fic 

(re-aim sensor)

.

2.  R a n g e   i s   s e t   t o o   h i g h . 

 

(Reduce Range)

.

SYMPTOM

Lights stay on 

continuously.

Lights flash on 

and off.

POSSIBLE CAUSE

1.  A flood lamp is positioned too close to 

the sensor or pointed at nearby objects 

that cause heat to trigger the sensor. 

(Reposition  the  lamp  away  from  the 

sensor or nearby objects)

.

2. Light control is pointed toward a heat 

source like an air vent, dryer vent, or 

brightly-painted  heat-reflective  sur-

face. 

(Reposition sensor)

.

3.  Light control is in Manual Mode. 

(Switch 

to Auto.)

1.  Heat or light from the lamps may be 

turning  the  light  control  on  and  off. 

(Reposition the lamps away from the 

sensor)

.

2.  Heat being reflected from other objects 

may be affecting the sensor. 

(Reposi-

tion sensor)

.

3.  Light control is in the Test mode and 

warming up. 

(Flashing is normal under 

these conditions)

.

4.  Light  may  be  leaking  through  the 

floodlamp reflectors. 

(Make sure the 

metal lamp protectors are installed.)

TROUBLESHOOTING GUIDE

TEN YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state 
to state or province to province.
For a period of ten years from the date of purchase, any malfunction caused by factory defective parts or workmanship 
will be corrected at no charge to you.

Not Covered -

 Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, 

and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of 
any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for incon-
venience, installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components 
that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY 
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR 
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, 
OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO 
LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL 
DAMAGES,  INCLUDING  BUT  NOT  LIMITED TO  ANY  LOSS  OF  BUSINESS  OR  PROFITS,  WHETHER  OR  NOT 
FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for 
all warranty requests.

TECHNICAL SERvICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning 

product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: 

www.hzsupport.com.

 

If the problem persists, call* for assistance at 

1-800-858-8501

 (English speaking only)

,

 7:30 AM to 4:30 PM CST 

(M-F). You may also write* to:
HeathCo LLC, P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of Pur-
chase, and Place of Purchase.

No Service Parts Available for this Product

Summary of Contents for SL-5412













Reviews: