background image

 

9

 

 

FW7I 23/07/14 

 

by first de-ashing and then using small pieces of wood and plenty of air to get flames issuing from the wood 
again. 

 
Refuelling on to a low fire bed 

If there is insufficient burning material in the fire bed to light a new fuel charge, excessive smoke emission 
can occur. Refuelling must be carried out onto a sufficient quantity of glowing embers and ash that the new 
fuel charge will ignite in a reasonable period. If there are too few embers in the fire bed, add suitable 
kindling to prevent excessive smoke 

 
Fuel Overloading 

Four good size logs is a sufficient quantity of fuel to achieve the rated output from this appliance. Never 
exceed this amount of fuel and never stack the fuel too high in the stove so as it touches the baffle or blocks 
the tertiary air holes as this may cause smoke to be produced.  
 

 
 
Shutting Down 

The stove will normally shut down by itself as the fuel is consumed. In order to shut down the stove for 
other reasons, close the primary air controls (if open), then close the secondary air control. If the controls are 
left in this position, the fire will eventually burn out. If you want to revive the fire open the secondary air 
controls fully. 

Warning! - 

The stove will remain 

very hot 

for a considerable time after the fire has died down or been 

extinguished. 

Warning!- Petroleum coke fuels or household waste must not be burnt on this appliance.  

 

Maintenance 

Inspect the inside of the firebox and above the baffle plate every week during use. 

See chimney cleaning 

section in section 3.1 Warnings and Important Information.

 Inspect the inside of the stove and the flue 

ways and ensure they are 100% clear after a period of disuse (e.g summer). 

Only use manufacturers 

recommended replacement parts on the appliance 
 
Seasonal Use 

Remove the baffle and inspect the inside of the stove and the flue ways and ensure they are 100% clear after 
a period of disuse, for example if the stove is not used during the warmer periods of the year. Also set the air 
controls to 50% to keep the appliance ventilated and stop the build-up of any moisture inside.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for FW7i















Reviews: