manualshive.com logo in svg

Heat & Glo SL-5F, Installation Manual

Share
Download
Heat & Glo SL-5F Installation Manual Download Page 64

64

Heat & Glo  • SL-5F, SL-7F Installation Manual  •  2499-980 Rev. L  •  10/19 

12-1/2 IN.

318 mm

20-3/4 IN.

527 mm

13-5/8 IN.

346 mm

EFFECTIVE LENGTH

32 IN. (813 mm) MIN.

35 IN. (889 mm) MAX.

A.  Vent Components Diagrams 

(continued)

Figure 12.6   PVI-SLP-B Vent Components

Optional Wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness

PVI-WH10

20 FT PV Wire Harness

PVI-WH20

40 FT PV Wire Harness

PVI-WH40

60 FT PV Wire Harness

PVI-WH60

80 FT PV Wire Harness

PVI-WH80

100 FT PV Wire Harness

PVI-WH100

PVI-SLP-B

Power Vent Inline

SLP-LPC

SLP Low Profile Cap

(Approved for use with PVI-SLP-B only)

Note:  

Wire harnesses required to power the PVI-SLP-B connect to the appliance and are ordered separately from 

PVI-SLP-B. Contact your dealer to order.

16 IN.

406 mm

15 IN.

(381 mm)

16-11/16 IN.

(424 mm)

9-3/16 IN.

(233 mm)

4-1/2 IN.

114 mm

16-11/16 IN.

424 mm

13-5/8 IN.

(346 mm)

12-1/2 IN.

(318 mm)

Note:  

The PVI-SLP-B requires a PV-IPI-CK be installed on this appliance.   The PV-IPI-CK is ordered separately from 

the PVI-SLP-B.  Contact your dealer to order.

Summary of Contents for SL-5F







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands