manualshive.com logo in svg

Heat & Glo SL-5F, Installation Manual

Share
Download
Heat & Glo SL-5F Installation Manual Download Page 48

48

Heat & Glo  • SL-5F, SL-7F Installation Manual  •  2499-980 Rev. L  •  10/19 

5-7/8 IN. 

MINIMUM

3 IN. 

MINIMUM

Note:  

Clearance from

opening to perpendicular wall.

UNLIMITED

FIREPLACE OPENING

See Dimension B on Appliance 

Dimension Diagram (Figure 3.1).

B.  Mantel and Wall Projections

WARNING! Risk of Fire! 

Comply with all minimum clear-

ances as specified. Framing closer than the minimums listed 

must be constructed entirely of non-combustible materials 

(i.e., steel studs, concrete board, etc.).

Figure 10.3  Clearances To Combustible Mantels Or Other 

Combustibles Above Appliance

Note:

 All 

measurements 

in inches.

5 6

7 8

9 10

3

4

5

12

11

10

9

8

7

6

TOP OF HOOD OR FIREPLACE OPENING

4

12

13

11

32

CEILING

Figure 10.7  Non-Combustible Zone

1/2 in. SHEETROCK 

OR COMBUSTIBLE 

MATERIAL

3-1/2 in.

1/2 in.

NON-COMBUSTIBLE ZONE

Figure 10.6  Non-Combustible Mantel Leg or Wall Projections 

 

(Acceptable on both sides of opening)

Note

: Clearance from opening 

to perpendicular wall.

UNLIMITED

TOP VIEW

FIREPLACE OPENING

See Dimension B on 

Appliance Dimension

Diagram (Figure 3.1).

3 IN. MIN.

6 IN. MAX.

Non-Combustible Mantel Leg or Wall Projection

Figure 10.5  Combustible Mantel Leg or Wall Projections 

 

(Acceptable on one side of opening)

Combustible Mantel Leg or Wall Projections

3 FT. MAXIMUM

TOP VIEW

2-7/8 IN. 

MINIMUM

1/2 IN. 

MINIMUM

FIREPLACE OPENING

See Dimension B on Appliance 

Dimension Diagram (Figure 3.1).

Note

: Clearance from opening 

to perpendicular wall.

Figure 10.4  Combustible Mantel Leg or Wall Projection  

(Acceptable on both sides of opening)

Summary of Contents for SL-5F







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands