manualshive.com logo in svg

Heat & Glo SL-5F, Installation Manual

Share
Download
Heat & Glo SL-5F Installation Manual Download Page 41

41

Heat & Glo  • SL-5F, SL-7F Installation Manual  •  2499-980 Rev. L  •  10/19 

Figure 7.16  Venting Through the Wall

Note: 

When using termination caps with factory-supplied 

heat shield attached, no additional wall shield firestop is 

required on the exterior side of a combustible wall.

Install Horizontal Termination Cap (DVP and 

SLP Pipe)

WARNING! Risk of Fire! 

The telescoping flue section of 

the termination cap MUST be used when connecting vent.

•  1-1/2  (38  mm)  minimum  overlap  of  flue  telescoping 

section is required.

Failure to maintain overlap could cause overheating 

and fire.

•  Vent termination must not be recessed in the wall. Siding 

may be brought to the edge of the cap base. 

•  Flash  and  seal  as  appropriate  for  siding  material  at 

outside edges of cap.

•  When  installing  a  horizontal  termination  cap,  follow 

the cap location guidelines as prescribed by current 

ANSI Z223.1

 and 

CAN/CGA-B149

 installation codes 

and refer to Section 4 of this manual.

CAUTION! Risk of Burns! 

Local codes may require in-

stallation of a cap shield to prevent anything or anyone 

from touching the hot cap.

NOTICE: 

For  certain  exposures  which  require  superior 

resistance to wind-driven rain penetration, a flashing kit and 

HRC caps are available.  When penetrating a brick wall, a 

brick extension kit is available for framing the brick.

 Termination Cap Specification Chart 

(depth without using additional pipe sections)

SL Series

DVP-TRAPK1

Top Vent 

Depth

DVP-TRAP1

Rear Vent 

Depth

DVP-TRAPK2

Top Vent 

Depth

DVP-TRAP2

Rear Vent 

Depth

N/A

3-1/8 in. to

5 in.

N/A

5-1/2 in. to

9-1/2 in.

DVP-HPC1

Top Vent 

Depth

DVP-HPC1

Rear Vent 

Depth

DVP-HPC2

Top Vent 

Depth

DVP-HPC2

Rear Vent 

Depth

N/A

3-1/8 in. to

5-1/4 in.

N/A

5-1/4 in. to

9-3/8 in.

DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

VENT DEPTH FROM BACK OF APPLIANCE TO

OUTSIDE SURFACE OF EXTERIOR WALL

(SEE CHART BELOW)

SLIP SECTION

CAN BE EXTENDED

INNER VENT

OUTER VENT

EXTERIOR

Summary of Contents for SL-5F







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands