Heat & Glo SL-350TRS-CE-D Installer'S Manual Download Page 1

Page: 1 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

Model:

SL-350TRS-CE-D

Installers Guide

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THIS APPLIANCE. THIS

INSTALLERS

GUIDE

MUST BE LEFT wITH APPLIANCE FOR FUTURE

REFERENCE.

0086

This is a room sealed appliance and no other ventilation is

required than what is provided.

These instructions are only valid if the following country symbol is

on the appliance. If this symbol is not present on the appliance,

it is necessary to refer to the technical instructions which will

provide the necessary information concerning the modification

of the appliance to the conditions of use for the country.

These instructions are valid for the following countries: GB, IE

wARNING

This appliance has been supplied with an integral barrier

to prevent direct contact with the fixed glass panel. DO

NOT operate the appliance with the barrier removed.

HOT SURFACES

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable

materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

• Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of

this or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance
- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a fire

or explosion may result causing property

damage, personal injury, or death.

Please contact your Heat & Glo dealer with any questions or

concerns. For the number of your nearest Heat & Glo dealer,

please visit www.heatnglo.com.

This product may be covered by one or more of the following patents: (United States) 5601073, 5613487, 5647340,

5890485, 5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122,

7098269, 7258116, 7470729, 8147240 or other U.S. and foreign patents pending.

2000-945B



Summary of Contents for SL-350TRS-CE-D
















































Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands

Heat & Glo SL-350TRS-CE-D, Installer'S Manual

Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands