Heat & Glo MONTANA MONTANA-36 Owner'S Manual Download Page 24 | Manualshive

Page: 24 / 44

background image

Heat & Glo LifeStyles Collection • Montana US-CAN • 4039-156 Rev C • 11/07

24

8

8

Finishing

A. Hearth Extension

A hearth extension must be installed with all

fi

replaces to

protect the combustible

fl

oor in front of the

fi

replace from

both radiant heat and sparks. See Figures 8.1 -8.3.

2 in. (51 mm)
required

High temperature
(300°F min.) continuous,
non-combustible sealant

Tile, stone or other
non-combustible material

Floor constructed of wood or
other combustible material

HX3 or HX4
Hearth Ext
or equivalent
insulation
(see Table below)

Fireplace

Protective
Metal Hearth
Strip

Figure 8.1 Hearth Extension Construction

1 in. (25 mm) overlap

Metal strips are placed 2 in. (51 mm) under the front
of the fireplace and must extend beyond the front
and sides of fireplace opening by 2 in. (51 mm).

Figure 8.2 Positioning the Protective Metal Hearth Strips

The hearth extension should slope away from the front of the

fi

replace and chase at 1/8 in. to 1/4 in. per foot. Spark strips

must be used on top of any combustible hearth materials
used for moisture management.

This

fi

replace has been tested and approved for use with a

hearth extension insulated to a minimum R value of 1.03.

To substitute materials for the factory-available hearth ex-
tensions, see Figure 8.3 and calculate insulation alterna-
tives as per Table 8.1 and the following formulas:

• Thermal conductivity per inch thickness =

k

• k = (BTU)(inch) / (foot

2

)(hour)(°F)

• Required thickness = Rk

• Thermal resistance per inch thickness =

r

• r = (foot

2

)(hour)(°F) / (BTU)(inch)

• Required thickness = R / rB.

A

B

C

Figure 8.3 Hearth Extension Dimensions

Fire Risk

• Metal hearth strips MUST be installed.
Sparks or embers may ignite

fl

ooring.

WARNING

Fire Risk

• Hearth extensions must be installed

exactly as speci

fi

ed.

High temperatures or hot embers may ignite
concealed combustibles.

WARNING

Table 8.1

CAT. #

A

B

C

HX3

in

52

16

8

mm

1321

406

203

HX4

in

66

20

12

mm

1676

508

305

Hearth Extension Insulation Alternatives-Total minimum R Value must equal 1.03

Material

k per inch

thick

r per inch

thick

Minimum

thickness

required

Hearth & Home HX3, HX4 (Micore 300™)

0.49

2.06

1/2 in.

USG Micore 160™

0.39

2.54

1/2 in.

USG Durock™ Cement Board

1.92

0.52

2 in.

Cement Mortor

5.0

0.20

5-1/8 in.

Common Brick

5.0

0.20

5-1/8 in.

Ceramic Tile

12.50

0.08

12-1/4 in.

Armstrong™ Privacy Guard Plus

0.46

2.18

1/2 in.

Marble

14.3-20.0

0.07-0.05

14-5/8 in. - 20-3/8 in.

¨

¨

«
...
22
23
24
25
26
...
»

Summary of Contents for MONTANA MONTANA-36













































Reviews:

No comments

Related manuals for MONTANA MONTANA-36

Brand: Rinnai Pages: 21

Brand: RAIS Pages: 18

Brand: Camina Pages: 48

Premos 18" Inset

Brand: Magiglo Pages: 52

Brand: Napoleon Pages: 108

Brand: ClassicFlame Pages: 18

Slimfocus mural

Brand: Focus Pages: 8

Brand: Lamborghini Caloreclima Pages: 196

Brand: Mendip Stoves Pages: 16

Tahoe DVP36PP32EN-1

Brand: Empire Comfort Systems Pages: 64

Brand: Firecraft Pages: 20

Brand: Majestic Pages: 36

Crea7ion EvoPlus Thales

Brand: GlammFire Pages: 20

Brand: Home Decorators Collection Pages: 41

Brand: Malm Fireplaces Pages: 10

Brand: Paramount Fitness Pages: 15

Brand: Paramount Fitness Pages: 18

focus rs plus remote

Brand: Paragon Fires Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands