background image

1

Heat & Glo  •  6000GBV, 6000GBV-IPI  •  2104-900  Rev. G  •  9/08  

Models:
6000GBV
6000GBV-IPI
6000GBV-LP
6000GBV-IPILP

Owner’s Manual

Installation and Operation

•  Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of 
this or any other appliance.

•  What to do if you smell gas   

-  Do  not  try  to  light  any  appliance                                                                       

-  Do not touch any electrical switch. Do not 

use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas suppli-
er’s instructions.

-  If you cannot reach your gas supplier, call 

the fi re department.

•  Installation and service must be performed 

by a qualifi ed installer, service agency, or the 
gas supplier.

WARNING:  If the information in these 

instructions is not followed exactly, a fi re 
or explosion may result causing property 
damage, personal injury, or death.

 

DO NOT DISCARD THIS MANUAL

CAUTION

Important operating 
and maintenance 
instructions included.

Installation and service of this appliance should be 
performed by qualifi ed personnel. Hearth & Home 
Technologies suggests NFI certifi ed or factory-trained 
professionals, or technicians supervised by an NFI certi-
fi ed professional.

DO NO

T

DISCARD

In the Commonwealth of Massachusetts:

•   installation must be performed by a licensed plumber 

or gas fi tter;

•  a CO detector shall be installed in the room where the 

appliance is installed.

Read, understand and follow 
these instructions for safe
installation and operation.

Leave this manual with 
party responsible for use 
and operation.

This appliance is only for use with the type(s) of gas indicated 
on the rating plate. 

WARNING

This appliance has been supplied with an integral barrier 
to prevent direct contact with the fi xed glass panel. DO 
NOT operate the appliance with the barrier removed. 

Contact your dealer or Hearth & Home Technologies if the 
barrier is not present or help is needed to properly install one.

HOT SURFACES

Glass and other surfaces are hot during 
operation AND cool down.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
• Keep children away

•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable 
materials.

•  Keep clothing, furniture, draperies and other fl ammable 

materials away.

Summary of Contents for 6000GBV















































Reviews: