HearthStone CARINA Owner'S Manual Download Page 6

Page: 6 / 43

Hearthstone Quality Home Heating Products, Inc

CARINA Series 8910

Installation Requirements

FIREPLACE REQUIREMENTS

• Insert must be placed within a code-conforming masonry fireplace or tested and listed factory-built

(metal) wood-burning fireplace. Repair any fireplace damage prior to installation.

• Because the insert uses a circulation blower, clean the fireplace, smoke shelf, and chimney prior to

installation.

• This heater may be placed in a bedroom. Please be aware of the large amount of heat this appliance

produces when determining a location.

• Installation and repair should be done by a qualified service person. The appliance should be inspected

before use and at least annually by a professional service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. It is imperative that the control compartment,

burners and circulating air passageways of the appliance be kept clean.

The Carina Fireplace
Insert inserts 14.75” deep
into the Fireplace cavity.

Summary of Contents for CARINA












































Search results

Summary of Contents for CARINA

Reviews:

Related manuals for CARINA

Brands by name

Popular brands

HearthStone CARINA, Owner'S Manual

Search results

Summary of Contents for CARINA

Reviews:

Related manuals for CARINA

Brands by name

Popular brands