Healthniture HBB500 Instructions For Use Manual Download Page 51

Page: 51 / 61

Check that the bed extension locks securely



Examine the power supply cord and mains plug – if damaged, replace the

complete assembly; do not use a rewireable plug



Examine all accessible flexible cables for damage and deterioration



Check all accessible nuts, bolts and other fasteners are present and
correctly tightened



Check any accessories fitted to the bed, paying particular attention to
fasteners and moving parts



Check the wire of the Mechanical Quick Release of the backrest (Mechanical
CPR) and notice if its tension is functional to the release of the backrest



Battery test

Check the condition of the backup battery by carrying out the following

test.

1. Disconnect the bed from the electricity supply.

2. Raise the mattress platform to maximum height

3. Raise the backrest and thigh sections as far as they will go.

4. Press and hold the CPR button and lower the mattress platform to
minimum height.

5. Apply maximum head down tilt (Trendelenburg).

6. Return the mattress platform to the level position.

7. Apply maximum foot down tilt (reverse Trendelenburg).

If this test is not completed successfully, connect the bed to the electricity

supply for at least 10 hours to recharge the battery then perform the test
again. If the bed fails a second time, contact the seller.

To maintain best performance see:

- chapter 7. Technical data / Electrical & Safety data / backup battery.

- chapter 7. Technical data / Transportation and storage / Caution.

IFU-HBB500-ENG-2021#ed02-May

Summary of Contents for HBB500






























































Search results

Summary of Contents for HBB500

Reviews:

Related manuals for HBB500

Brands by name

Popular brands

Healthniture HBB500, Instructions For Use Manual

Search results

Summary of Contents for HBB500

Reviews:

Related manuals for HBB500

Brands by name

Popular brands