STA-RITE Heater
1. Turn power off to heater.
2. Remove upper jacket and open the control box.
3. Remove the jumper for the “fireman’s switch.
4. Wire to the Aqua Plus 16v using wire rated for 105°C minimum.
STA-RITE
Terminal
Board
Operating
‘Control
Fireman’s
Switch
Hayward Variable Speed Pump (VSP) Wiring and Address Setting
Refer to your TriStar or EcoStar manual(s) for proper low voltage communication wiring between the Pro Logic
and the Hayward Variable Speed Pump.
A pump address must be configured for each VSP used in the system. This address is entered into the VSP’s
configuration menu. Refer to the table below to determine which address to use for your specific pump and Pro
Logic. Select the proper address based on which output will be used and the model VSP you are configuring.
18
25
Pool/Spa Config.
+ to view/change
Pool/Spa Setup
Pool and Spa-Std
Spa Spillover
Enabled
Heaters
Htr1=Spa,Htr2=Pool
Filter Operation
Spa Spillover
Push to access Pool/Spa options
Rotates between Pool and Spa-Std
, Pool and Spa-Dual,
Pool Only, and Spa Only options
(default)
Toggle between Enabled and Disabled
Spa Spillover
(default)
Toggle between Htr1=Spa, Htr2=Pool (default) and Shared Heaters
Toggle between Pool Only
and Spa Spillover options
(default)
Move to previous/next configuration menu
Move to next menu item
Move to next menu item or previous/next configuration menu
Move to next menu item
Move to previous/next configuration menu
if “Pool and Spa-Std or Dual” is
selected and if “Spa Spillover” is enabled
Spa - CountDn
00:30
Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15..., (default is 4:00))
Move to next menu item
if “Pool and Spa-Std” is selected
if “Pool and Spa-Dual” is selected
if “Pool and Spa-Std or Dual” is selected
V1=Aux1, V2=Aux2
Disabled
Toggle between Enabled and Disabled (default)
if “Pool Only” or “Spa Only” is selected
Move to previous/next configuration menu
Filter Off Valve
Change: Enabled
Toggle between Enabled
and Disabled
(default)
if “Pool and Spa-Std” is selected
Move to previous/next configuration menu
Pool/Spa Setup
If “Pool Only” or “Spa Only” are selected, then the pool/spa valves are not needed and pushing the
POOL/SPA button on the display/keypad will have no effect. If “Pool and Spa-Std” is selected, then
the pool/spa suction and return valve actuators should be connected to the Pro Logic. Pressing the
POOL/SPA button on the display/keypad will allow the homeowner to alternate between pool and spa
operation. If “Pool and Spa-Dual” is selected, then only the Pool/Spa return valve actuator should be
connected to the Pro Logic.
Heaters
This menu will only appear if Pool/Spa setup is set to “Pool and Spa-Dual”. This allows the heater(s)
to either be shared between the pool and spa (“Shared” selected) or for Heater1 to be dedicated to the
spa and Heater2 to be dedicated to the pool (“Htr1=Spa, Htr2=Pool” selected).
Spa CountDn
This menu will appear only if Pool/Spa Setup is set to “Pool and Spa-Std”. This setting is the time,
after you manually switch the Pool/Spa valves to “Spa Only”, until the Pro Logic automatically
returns the valves to their previous positions. It is programmed in increments of 5 minutes, from
“Manual On/Off” (0 minutes) to
“21:00” (21 hours).
The filter is forced on during this time period.
Spa Spillover
When spa spillover is “Enabled” and “Pool and Spa-Std”, the homeowner will be able to rotate
through “Pool Only” (both suction and return valves switched to pool), “Spa Only” (both suction and
return valves switched to spa) and “Spillover” (suction valve switched to pool and return valve
switched to spa) by successive presses of the “Pool/Spa” button. For “Pool and Spa-Dual”, only
“Pool Only” and “Spillover” are available.
Filter Operation
If “Spa Spillover” is selected, the Pro Logic will automatically switch the pool/spa suction and return
valves to “spillover” at the start of the programmed pool filtering time period or when the super-
chlorinate function is turned on. The valves will remain in this position for the remainder of the super-
chlorinate period. This option is usually preferable because both the pool and spa water will be
filtered and sanitized.
FILTER - all Pro Logic models
AUX1 - all Pro Logic models
Dual Equipment Spa Filter - all models
A
2 - all Pro Logic models
A
3-A
6 - PS8 & PS16 models
A
7-A
14 - PS16 models
UX
UX
UX
UX
UX
LIGHTS - all Pro Logic models
Pro Logic Output
This is the output used to control the VSP.
Note that the VSP should be wired to this
output’s corresponding relay.
VSP Address
This is the name that should be selected
under “Set COMM bus address” (EcoStar)
or “*H.Comm ADDR.” (TriStar) within the
VSP’s Configuration Menu.
“001” - Tristar
“Pool Filter” - EcoStar
“002” - Tristar
“
” - EcoStar
Aux1 / Spa Filter
“Lights Button” - EcoStar only
Aux2-Aux14 - EcoStar only
(use same as Pro Logic Output)
