Havospark AquaJet Dive H2 Instructions Manual Download Page 12

- 22 -

- 23 -

EN

EN

Notice for use

02 Notice for use

Aquajet Dive H2 Must nots

1. 

AII users must not attempt to handle, modify, repair or insert foreign objects into the propeller cage before, during or 

after the operation of the Aquajet Dive H2.

2. 

AII users must not operate or use the Aquajet Dive H2 in the presence of electrical storms, thunder storms, typhoons, 

hail, or if wave height is level 3 or greater, etc.

3. 

AII users must not use substitute parts, components, or home made devices such as chargers, battery packs or the 

like, doing so may compromise the operation of the Aquajet Dive H2 and may void your warranty.

4. 

AII users must not use the Aquajet Dive H2 in densely populated areas in order to avoid potential collision with boats, 

sea life, other swimmers, divers, other recreational sports enthusiasts or the like.

According to the WMO World Meteorological Organization sea state code 3 is wave heights of (1ft 8 in to 4 ft 1in)

Remember: Aquajet dive H2 is a high speed, single user device propelled at speeds up to 5.6 MPH. It is critical 

to maintain a mindful lookout for the safety of both you as the operator and potential danger to others. At any 

time should the situation become unsafe, please return to the safety area immediately!

Product Structure 

03 Product Structure Diagram

A01

Head cover

Fuselage

Fast-dismantle button

Wrist strap

V-shaped tail cover

Right speed control button

Lock latch

Power switch

Display screen

Speed control 

switch

Right wing

Left wing

Bottom tail cover

A11

A10

A09

A08

A14

A12

A13

A04

A03

Action sports

camera mount

A02

A05

A06

A07

Belly

Summary of Contents for AquaJet Dive H2



















Reviews: