HOOD CLEANING
Stainless steel is known for its ability to be a clean
surface that resists corrosion an rust. Dirt, dust and
grime, however, put stainless at risk for corrosion
and rust. Luckily, stainless steel responds well to
cleaning, never wearing out from excessive clean
ing, as long as certain rules are followed.
1.Water and a cloth.
Routine cleaning can be ac
complished by using warm water and a cloth. This
is the least risky option for cleaning stainless steel.
Dry with a towel or cloth to prevent water spots.
Wipe in the directions of the polish lines.
2. Mild detergent, (dish washing liquid) and
cloth.
For cleaning that needs more power, mild
detergent and warm water can do a great job with
out damaging the stainless steel. Make sure you
rinse the surface thoroughly to prevent staining and
spotting. Towel dry to prevent water spots which
can be caused by minerals in water.
3. Glass cleaner for fingerprints.
Fingerprints are
one of the biggest complaints about stainless steel,
but can be taken care by using glass cleaner or
household ammonia. Rinse thoroughly and towel
dry. There are some newer types of finishes for
stainless steel that resist fingerprints, a must if your
pint-sized helpers leave their mark on your stain
less steel appliances.
4. Stainless Steel Cleaner.
If you've had staining
or scratching, or need to polish your stainless steel,
a stainless steel cleaner may be a good option.
Some of these cleaners and polishes can help min
imize scratching and remove stains. They also can
polish stainless steel surfaces nicely. Read the di
rections on the stainless steel cleaner and test in
an inconspicuous spot. Be sure to rinse thoroughly
and towel dry.
Warning- When cleaning the hood, never spray
cleaning agent directly on the controls; spray it
on the cleaning cloth and wipe the control with
it. Spraying cleaning agent directly on the con
trol will cause unexpected keyboard activation.
Do not use
any steel or stainless steel wool or any
other scrapers to remove stubborn dirt.
Do not use
any harsh or abrasive cleanser.
Do not
allow dirt to accumulate.
Do not
let plaster dust or any construction resides
reach the hood. During construction or renovation,
cover the hood to make sure no dust sticks to
stainless steel surface.
AVOID : when choosing a detergent
-Any cleaners that contain bleach will attack stain
less steel.
-Any products containing:
chloride, fluoride, io
dide, bromide
will deteriorate surfaces rapidly.
-Any
combustible products
used for cleaning
such as
acetone, alcohol, ether, benzol,
etc., are
highly explosive and should never be used close to
a range.
Auto-cleaning function
(Only for Model C395)
Use the white water kettle provided, mix with 2 por
tion of degreaser (DO NOT USE detergent) and 8
portion of water.
We recommend to use 409 degreaser.
Remove the cap at the top left of the range hood,
Fill in the mixer into the hole (water tank).
It can serve up to 8-10 times of Auto-cleaning func
tion.
Stop to fill if over flow.
Status
Method of fixing
Bulb does
Check the light bulb, some base too flat
not light
cannot touch the base.
Check for damaoed control oanel
Check connection of power plug
Check whether the vane is blocked
Motor does
Lubricate the motor
not work
Repair or replace damaged control panel
Replace the capacitor
Replace the motor
Machine
Fasten the body
vibrates
Check for damaged vanes
when
Check if the vanes are installed well
switch on
Fasten the motor
Regulate bob-weight or replace the
Big noise
vanes
Check whether some matters drop into
the air chamber, like damper.
Lower the hood properly
Weak sue-
Do not open too many windows for im-
lion
proving the suction environment
Replace the motor and the capacitor
Oil leakage Remain the body level
Replace the sealant
Unworka-
Replace the cleaning bump
ble clean-
ing
Replace the control machine
Page: 14
Maintenance
C395 (with Auto-clean function) - using this function weekly to maintenance the inside
cleanliness of the hood.
After long time of using the hood (about 6 months), you will see grease retained at the grease
guard and blowers (inside the hood).
Follow the steps below
Important -
Switch power off at service panel and lock service disconnection means to pre
vent power from being switched on accidentally.
1. Disengage the small round grease guard cups from the grease guard by turning counter
clockwise and remove.
2. Remove the screw retaining the grease guard to the hood.
3. Remove the grease guard from the hood. Then remove the bottom panel.
4. Unscrew the clips and remove the wheel grease collector.
5. Remove the wheel center cap.
6. Loosen the wheel set screw in order to disengage the wheel from its motor shaft.
Let soak for 30 minutes all removed parts in warm soapy water. Then wash with nylon brush,
rinse and dry completely before reinstalling.
NOTE:
When reinstalling the wheel, align the
end of the set screw with the flat part of the
motor shaft (see the picture at right hand
side )
Page:15
Hauslane
267 Wattis Way, San Francisco, CA 94124
Tel: 1-800-929-0168 E-mail: [email protected]
Hauslane
267 Wattis Way, San Francisco, CA 94124
Tel: 1-800-929-0168 E-mail: [email protected]