manualshive.com logo in svg

Haulotte HA20RTJ O, Operator'S Manual

Share
Download
Haulotte HA20RTJ O Operator'S Manual Download Page 97

A

B

C

D

E

F

G

H

I

97

 4000388880 

E 06 15

GB / USA

E

- General Specifications

HA20RTJ - HA20RTJ O - HA20RTJ PRO - HA61RTJ O - HA61RTJ PRO

 5.3.3 - Safety precautions

• Check the work area for overhead clearances,

obstructions or other possible hazards. 

• When driving, position the platform so as to provide

the best visibility possible and avoid any blind spots. 

• Always ensure that the chassis is never driven any

closer than 1 m (3 ft3 in) from holes, bumps, tilts,
obstructions, debris and ground coverings that may
hide dangers. 

•  During operation, keep all the parts of the body inside

the platform. 

• To position the machine close to obstacles, it is

recommended to use boom movements (arm, boom,
etc.) instead of the drive movements. 

• Do not drive fast in narrow or cluttered areas. Keep

speed under control while making turns or sharp
bends. 

• Do not use the  Activ' Shield Bar as a handhold. To

prevent unintentional activation of the system. 

Summary of Contents for HA20RTJ O

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands