manualshive.com logo in svg

Haulotte HA20RTJ O, Operator'S Manual

Share
Download
Haulotte HA20RTJ O Operator'S Manual Download Page 70

70

 4000388880 

E 06 15

GB / USA

D

- Operation instructions

HA20RTJ - HA20RTJ O - HA20RTJ PRO - HA61RTJ O - HA61RTJ PRO

3 -  Platform control box

 3.1 -  T

O

 

START

 

AND

 

STOP

 

THE

 

MACHINE

To start the machine : 

At the ground control box : 

•  Check that the E-stop button ( 15 ) is not pressed in. 

•  Turn  ON/OFF key switch ( 18 ) to the right to turn  ON. 

•  Turn the control box energizing selector switch ( 229 ) to the left to energize platform box. 

At the platform control box : 

•  Check that the E-stop button ( 46 ) is not pressed in. 

•  Push the starter selector switch ( 230 ) upwards. During pre-heating LED ( 102 ) at platform

display panel and LED ( 5 ) at ground display panel will light up. Pre-heating begins and the
engine starts. 

•  Allow the engine to heat up and initialize. 

To stop the engine : 

•  Push engine start switch ( 230 ) upwards. 

Summary of Contents for HA20RTJ O

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands