manualshive.com logo in svg

Haulotte HA20RTJ O, Operator'S Manual

Share
Download
Haulotte HA20RTJ O Operator'S Manual Download Page 32

32

 4000388880 

E 06 15 

GB / USA

HA20RTJ - HA20RTJ O - HA20RTJ PRO - HA61RTJ O - HA61RTJ PRO

B

- Familiarization

 3.2.2 - Display Panel (LED'S  1 - 10)

I n d i c a t o r s   /   C l u s t e r

Marking

Description

LED 1

Overriding system : 

• Stays illuminated with Overriding system switch ( 245 ) in use.

LED 2

Fault : 

• Rapid flashing if a fault is active (current defect)
• Flashing if the service counter is at zero

LED 3

Radius limitation : 

• Not used

LED 4

Overload (For CE and AS standards only)

• Flashing : Faulty weighing system
• Illuminated in case of overload

LED 5

Combustion engine pre-heating : 

• Illuminated while engine is pre-heating
• Off if engine started and if post-heating

LED 6

Engine warning : 

• Flashing :  5 flashes when ignition is switched on if service counter is less than  20 hours
• Constantly on : If the service counter is at zero

LED 7

Engine shutdown : 

• Lighted in case of major engine fault (e.g. engine overheating, oil pressure, alternator fault, etc.)
• Lighted in case of faults managed by the engine ECU

LED 8

1

1.

If engine quipped with Particulate Filter Regeneration

 DPF regeneration inhibited (DPF : Diesel Particulate Filter)

LED 9

2

2.

If engine quipped with Particulate Filter Regeneration

 DPF regeneration required : 

• Permanently lighted if the particle filter requires regeneration with a high clogging level (DPF : Diesel Particulate 
Filter)

LED 10

3

3.

If engine quipped with Particulate Filter Regeneration

 DPF regeneration in progress, high temperature in the exhaust system ( HEST ) (HEST : High 
Exhaust System Temperature)

Summary of Contents for HA20RTJ O

















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands