background image

 

 

 

 

 

 

IMPORTANT ELECTRICAL INFORMATION 

WARNING! 

1) 

NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the 

power cord away from any moving part of the treadmill including the elevation mechanism 

and transport wheels. 

2) 

NEVER operate treadmill on Generator or UPS power supply. 

3) 

NEVER remove any cover without first disconnecting AC power. 

4) 

NEVER  expose  this  treadmill  to  rain  or  moisture.  This  treadmill  is  not  designed  for  use 

outdoors, near a pool, or in any other high humidity environment. 

 

IMPORTANT OPERATION INSTRUCTIONS 

1) 

Insert the power plug into the socket directly. Current load should be correct. 

2) 

The  constant  running  time  is  less  than  2  hours.Be  sure  to  read  the  entire  manual  before 

operating your machine. 

3) 

Understand that changes in speed and incline do not occur immediately. Set your desired 

speed  on  the  computer  console  and  release  the  adjustment  key.  The  computer  will  obey 

the command gradually. 

4) 

Use  caution  while  participating  in  other  activities  while  walking  on  your  treadmill;  such  as 

watching television, reading, etc. These distractions may cause you to lose balance or stray 

from walking in the centre of the belt; which may result in serious injury. 

5) 

In  order  to  prevent  losing  balance  and  suffering  unexpected  injury, 

NEVER

  mount  or 

dismount  the  treadmill  while  the  belt  is  moving.  This  unit  starts  with  a  very  low  speed. 

Simply  standing  on  the  belt  during  slow  acceleration  is  proper  after  you  have  learned  to 

operate this machine. 

6) 

Always hold on to handrail while making control changes. 

7) 

A safety key is provided with this machine. Remove the safety key will stop the walking belt 

immediately;  the  treadmill  will  shut  off  automatically.  Insert  the  safety  key  will  reset  the 

display. 

8) 

Do not use excessive pressure on console control keys. They are precision set to function 

properly with little finger pressure. 

9) 

This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their  safety,  Children  should  be  supervised  to  ensure  that  they  do  not  play  with  the 

appliance. 

10) 

Please consult your doctor at first before running, if you have one of the following diseases:   

a. Cardiopathy,  hypertension,  sugar  diabetes,  respiratory  disease,  smoking,  and  other 

chronic diseases, complication disease. 

b. If you are over 35 years old and heavier than common weight. 

c. Women in pregnant or in breasting period.   

11) 

Please stop exercising immediately and consult your doctor when you feel           

giddy, surfeit, thorax ache or other symptoms. 

12) 

Please  drink  adequate  water  after  taking  exercises  on  our  treadmill  for  more  than  20 

minutes. 

Summary of Contents for GORDION

























Reviews: