Conveyor Feeder Guide
The conveyor feeder guide is installed at the factory and can
be used in two positions See 4 .
1. When in the upright position, the toaster is set for automatic
feed. Bread products enter the toaster simply by placing them
on the feeder guide and releasing.
2. For manual feeding of product, tip the feeder guide until it rests
on top of the unit. In this position, bread products can be
manually loaded by placing them directly on the conveyor belt.
CAUTION
Some exterior surfaces on the unit will get hot. Use caution
when touching these areas to avoid injury.
Front and Rear Discharge
Toast-Qwik units can be set up so product discharges at either
the front or rear of the unit.
1. For front discharge, install the toast collector pan in the front
of the unit as shown in 4 . Pull the vane handle
(rear of unit, See 6 ) until the discharge vane pivots fully
in the rearward position.
2. For rear discharge, install the toast collector pan on the rear
of the unit as shown in 6 . Push the vane handle, see 6
forward until the discharge vane pivots fully in the forward
position.
Toast Crumb Tray
The toast crumb tray can easily be removed by sliding it out from
the front of the unit See 4 .
Thermostat Adjustment
(TQ-700 Series except TQ-700H-S)
The thermostat adjustment screw is located on the lower right front
of the unit See 4 . This thermostat controls the toasting chamber
temperature. The thermostat is preset at the factory, but may be
adjusted as follows:
1. Using a small screwdriver, carefully pry the black plastic plug
from the cabinet.
2. Turn the adjustment screw See 4 clockwise to increase
temperature or counterclockwise to decrease the temperature.
NOTE:
Do not turn screw more than 1/8 turn at a time. Allow
at least 5 minutes for temperature to stabilize.
3. Re-install black plastic plug after adjustment is complete.
!
8
Form No. TQCEM-1002
ASSEMBLY
1. Remove unit from box.
2. Remove information packet.
To prevent delay in obtaining
warranty coverage, fill out and mail in warranty card.
3. Remove tape from Crumb Tray and Toast Collector Pan.
NOTE:
Remove the tube of lubricating oil taped to the bottom
of the toast collector pan. Retain for future lubrication of the gear
motor.
LOCATION
CAUTION
Do not locate the toaster in an area subject to excessive
temperatures or grease from grills, fryers, etc. Excessive
temperatures could cause damage to the unit. Do not place
toaster in an area that restricts air flow around the motor
compartment. Do not place toaster in direct discharge path
of air conditioning vent or makeup air vent.
WARNING
For safe and proper operation, the unit must be located
a reasonable distance from combustible walls and materials.
If safe distances are not maintained, discoloration
or combustion could occur. Do not locate toaster under shelving
or closer than 31 cm (12") from the ceiling.
WARNING
Allow a minimum of 3 cm (1") clearance along the sides. Allow
a clearance of 31 cm (12") along the front and rear discharge
to ensure proper operation and safety.
CAUTION
Locate the unit at the proper counter height, in an area that
is convenient for use. The location should be level to prevent
the unit or its contents from accidentally falling, and strong
enough to support the weight of the unit.
CAUTION
Do not place anything on top of the toaster; doing so could
damage toaster or subject personnel to possible injury.
SET-UP
CAUTION
The toasting of coated products such as garlic bread, cheese
sandwiches and sweet rolls is NOT recommended. Residue will
reduce toaster performance and could possibly ignite inside
the toaster.
CAUTION
When setting up the unit for operation, make sure power
to the unit is off and the toaster is at room temperature. Failure
to do so could result in personal injury.
!
!
!
!
!
!
INSTALLATION
Summary of Contents for TOAST-QWIK TQ-300
Page 53: ...Form No TQCEM 1002 52 NOTES ...
Page 54: ...Form No TQCEM 1002 53 NOTES ...
Page 55: ...Form No TQCEM 1002 54 NOTES ...
